Contents
1. What a Waste WPC Recycling Pelletizing Line Is and Who Buys One
The machine and the product it makes
A waste WPC recycling pelletizing line takes discarded wood plastic composite furniture, decking, pallets and panels and turns them back into uniform pellets that can be used in a new extrusion or molding process. The feed is a difficult mixture of thermoplastic, wood fiber, coupling agent, pigment and whatever the product accumulated in service. The line breaks that mixture down, removes metal and contamination, controls moisture, melts it gently, filters the melt, removes volatiles and cuts the strand into pellets. The output is not virgin resin and it is not a filler masterbatch; it is a secondary WPC compound with a known polymer family, a known fiber content and a repeatable melt flow.
Three buyer groups and their real requirements
The first buyer is a WPC furniture or decking manufacturer with its own trim and reject stream, usually looking to recover 5 to 15 percent of its own output without buying a full waste plant. The second is a professional recycler collecting post consumer WPC from demolition, municipal yards and furniture take back programs, whose decision turns on sorting accuracy and pellet market price. The third is a furniture group with a take back obligation that needs a line able to process several colors and several polymer families in campaigns. Each buyer needs different flexibility: the captive user wants low changeover cost, the merchant recycler wants throughput and purity, and the take back operator wants traceability by collection batch.
What the line does not do
The line does not sort mixed municipal waste automatically, it does not remove paint down to bare polymer, and it does not restore degraded resin to virgin performance. Sorting, surface preparation and compound design are separate decisions that begin upstream or in the formulation stage. A buyer should also be clear that a line built for clean rigid PP flake will not run WPC furniture scrap successfully without changes to feeding, filtration and degassing, because wood fiber and coatings behave very differently from clean plastic flake.
2. What WPC Furniture Scrap Actually Contains
The polymer family
Most outdoor WPC furniture and decking is based on polyethylene, often high density polyethylene, with polypropylene used where higher stiffness is needed and PVC used in some indoor panels and profiles. Wood flour or wood fiber makes up roughly 30 to 60 percent of the compound, and a coupling agent, usually a maleated polyolefin, binds the hydrophilic fiber to the hydrophobic polymer. Pigments, ultraviolet stabilizers, fungicides and flame retardants are present in small percentages. The recycler has to know which family is in the incoming load before choosing a screw profile or a temperature window, because a single PVC profile in a polyethylene batch can contaminate the whole lot.
The non plastic fraction
Furniture scrap carries steel screws, brackets, aluminum inserts, adhesive residue, surface coatings and embedded grit from outdoor use. Wood that has been outdoors for years may carry moisture deep inside the fibers and degraded surface layers that turn dark when heated. A load of decking boards also brings concrete dust and soil, which are abrasive and show up as hard particles in the melt. The line needs magnetic separation, eddy current separation where aluminum is expected, a granulator with wear resistant knives, and filtration that can handle a realistic solids load rather than a laboratory ideal.
How composition drives the process
Wood fiber content sets the upper melt temperature because cellulose starts to darken and degrade above roughly 200 degrees Celsius, while the polymer may tolerate more. That conflict is the central process problem. Fiber also raises melt viscosity and abrasion, so the screw needs lower shear than a pure plastic recycling screw and the barrel needs a wear resistant finish. Regrinding WPC also shortens the fibers; every pass through a granulator reduces aspect ratio and therefore the reinforcing effect, which is why the recycled pellet is normally aimed at less demanding parts than the original board.
3. Why WPC Scrap Is Harder to Recycle Than Pure Plastic
Thermal history and degraded interfaces
A WPC board has already been melted once during profile extrusion, and the wood surface has already been treated by a coupling agent. Reheating breaks some of those bonds and shortens some polymer chains, so the melt flow index of the recyclate moves away from the original grade. The coupling layer is also partly consumed, meaning a second pass without fresh coupling agent produces a pellet with poorer wood to plastic adhesion. This is why recompounding additives are not optional for high quality WPC recyclate; they restore the interface that the first service life used up.
Wood moisture and steam at the die
Dry wood flour can hold several percent moisture after rain or humid storage, and water trapped inside fiber bundles flashes to steam in the barrel. The result is a porous strand, surface splay and a pellet that breaks in handling. A line processing WPC scrap therefore puts more effort into drying than a line processing clean rigid flake, and it uses vacuum degassing at two or three points rather than one. Official rigid flake lines specify feed moisture at or below 2 percent and particle size below 13 millimeters; WPC scrap should be treated as a stricter case even when the polymer fraction is easy to melt.
Contamination that changes color and odor
Charred wood, rubber gaskets, silicone sealant and paint become visible dark specks after melting. A modern recycling line removes these materials early, before they break into smaller fragments, using a preconditioning stage and a belt melt filter. Removing a cellulose particle before it passes through the screw is far easier than filtering the same particle after the screw has shredded it. Odor follows the same logic: volatiles released early can be drawn off by vacuum, while volatiles released at the die end up in the pellet and in the workshop air.
4. Sorting Collection Streams and Keeping Polymer Families Apart
Identifying PE, PP and PVC streams
Polyethylene WPC is usually lighter and more flexible, and it floats in a simple density separation step; PVC based WPC is denser and often sinks. Polypropylene sits between the two in behavior and is best identified by melt point testing or by a rapid spectral handheld check at the intake. Furniture scrap arrives as assembled parts, so a board with an aluminum core or a PVC edge strip must be broken down before the polymer can be classified. A recycler that accepts loads without a written material declaration will spend the saving several times over on rejected pellets.
Removing fasteners and metal inserts
Overbelt magnets remove ferrous screws and staples after the first shredding stage, and an eddy current separator handles aluminum where furniture frames are present. Metal that reaches the granulator destroys knife edges and metal that reaches the extruder damages the screw and barrel. A single missed steel bracket can cost more in downtime than a week of separator operation. Wanplas recommends a metal detector after the final grinding step as a last barrier, with an automatic diverter rather than a manual pick.
Batch identity and supplier grading
Pellets from WPC scrap are sold on consistency, so every incoming load should be assigned a batch record holding the supplier, the collection route, the estimated polymer family, the wood content and the moisture reading. Loads from a single furniture model can be run together; loads from mixed demolition should be treated as lower grade and directed to less demanding applications. A simple traffic light system at intake, green for known single polymer, amber for mixed but sorted, red for unknown, prevents most quality disputes before the material ever reaches the extruder.
5. Size Reduction from Whole Panels to Controlled Flake
Primary shredding
Whole WPC boards and assembled furniture pieces are too large for a granulator, so a low speed, high torque shredder reduces them to 40 to 100 millimeter pieces. Slow cutting matters because it limits heat build up in the wood fiber and avoids smearing the polymer over the fiber surface. A shredder for this duty uses hardened steel knives with a wear resistant coating and a reversible rotation cycle to clear jams. Throughput of 500 to 1,000 kilograms per hour costs roughly 25,000 to 90,000 US dollars, and a spare knife set adds 2,000 to 8,000 US dollars.
Secondary grinding and screen selection
A granulator with water injection or a dry cutting chamber then reduces the shredded pieces to flake below 13 millimeters, which is the practical upper limit for stable feeding on a rigid flake extrusion line. Screen size is chosen as a compromise: smaller flake dries faster and melts more evenly, but produces more fines that are lost in washing and dust collection. Most WPC recyclers run 6 to 12 millimeter screens and accept a fines fraction of 3 to 8 percent. Knife clearance should be checked every shift, because a dull blade heats the wood and creates a dark streak that survives the melt filtration stage.
Dust collection and knife wear
Wood plastic dust is abrasive and combustible, so the grinding area needs local extraction, a bag filter and a housekeeping schedule that prevents accumulation on beams and floors. Knife life on WPC scrap is typically 200 to 600 operating hours, far shorter than on clean plastic, because the fiber acts as an abrasive. Budget 8,000 to 25,000 US dollars a year for knives and screen spares on a mid size line. Grinding is also the noisiest part of the plant, and acoustic enclosure adds 10,000 to 30,000 US dollars but is often required by the site permit.
6. Washing, Moisture Control and the Two Percent Limit
What has to be washed off
Outdoor WPC furniture carries soil, algae residue, sunscreen, paint and loose wood fibers. A friction washer with water injection removes most loose contamination, followed by a hot wash at 50 to 70 degrees Celsius when oil or paint is present. Unlike a food packaging line, a WPC line does not need caustic washing for protein or starch, so the water treatment burden is lower. The aim is not food grade cleanliness but a flake that will not char at the die and will not overload the melt filter within an hour.
Dewatering and thermal drying
A horizontal centrifuge brings flake moisture from 10 to 15 percent down to 5 to 8 percent, and a thermal dryer finishes the job to below 2 percent. Wood fiber holds water inside its structure, so residence time matters more than surface heating; a fast air knife cannot replace a properly sized dryer. A combined dewatering and drying package for 500 to 1,000 kilograms per hour costs 35,000 to 130,000 US dollars and consumes roughly 0.05 to 0.12 kilowatt hours per kilogram. Dryer exhaust should be filtered before release because it carries fine wood dust.
How moisture is measured on the floor
A loss on drying balance gives a result in 15 to 30 minutes and should be used at intake, after the dryer and before every grade change. A line that relies on the dryer’s set temperature alone will eventually run wet material, because wetter feed changes the residence time requirement. Operators should record moisture alongside melt pressure and screen differential pressure, since a rising screen pressure after a moisture spike is a reliable sign that steam is carrying fines into the melt. Wanplas includes a moisture log template in the line handover package.
7. Complete Line Architecture and Equipment Price List
The twelve sections of a WPC recycling line
The full plant runs from intake to packed pellet: shredder, magnetic and eddy current separation, granulator, washing and drying, preconditioning, extruder, melt filtration, vacuum degassing, pelletizing, dewatering and classification, control system and bagging. The table below gives a realistic budget for a 1,000 kilogram per hour line, with prices in US dollars for equipment only and a standard industrial finish. A 300 to 500 kilogram per hour plant serving one furniture factory sits near the lower end, while a 2,000 kilogram per hour merchant plant with full water treatment and double filtration sits well above the upper end.
| Line section | What it controls | Typical price in US dollars |
|---|---|---|
| Intake conveyor and sorting table | Batch identity and manual rejection | 20,000 – 60,000 |
| Low speed shredder | Piece size and heat build up | 25,000 – 90,000 |
| Magnet, eddy current and metal detector | Screw and barrel protection | 18,000 – 65,000 |
| Granulator with wear resistant knives | Flake below 13 millimeters | 25,000 – 85,000 |
| Friction washer, hot wash and centrifuge | Soil, coating and surface water | 55,000 – 180,000 |
| Thermal dryer and dust filter | Moisture below 2 percent | 35,000 – 130,000 |
| Preconditioning and agglomeration unit | Bulk density and feed stability | 60,000 – 190,000 |
| Single screw extruder, 100 to 150 millimeter | Gentle melting and output | 120,000 – 320,000 |
| Belt melt filter and continuous screen changer | Char, wood and rubber removal | 70,000 – 200,000 |
| Triple vacuum degassing package | Steam, odor and volatiles | 35,000 – 100,000 |
| Water ring pelletizer and classifier | Pellet shape and moisture | 45,000 – 150,000 |
| Control system, weighing and bagging | Recipe, data and pellet packing | 30,000 – 90,000 |
Reading the total
The midpoints add to roughly 0.87 million US dollars for a complete 1,000 kilogram per hour plant, with a realistic spread of 0.45 to 1.60 million US dollars across the columns. Freight, foundations, water treatment and commissioning add 90,000 to 260,000 US dollars. A compact 300 to 500 kilogram per hour plant for a single furniture maker costs 150,000 to 350,000 US dollars with cold washing and strand pelletizing. Wanplas quotes each section separately so that a buyer can match the plant to the actual waste stream instead of paying for capacity that will stand idle.
8. Preconditioning, Agglomeration and Stable Feeding
Why flake alone feeds badly
Dry WPC flake has low bulk density and inconsistent flow, so a screw feeder sees surges that show up as melt pressure swings and pellet weight variation. A preconditioning unit cuts, homogenizes, heats, dries, compacts, buffers and doses in one stage, delivering a dense and thermally prepared feed to the extruder. Because the material arrives already warm, the screw can be shorter and the melt residence time drops, which matters when wood fiber is sensitive to heat. The unit costs 60,000 to 190,000 US dollars and is the single most useful upgrade for a plant handling mixed WPC shapes.
Early removal of cellulose and rubber
A preconditioning stage also gives the plant a chance to remove light contamination before it is shredded finer by the screw. Cellulose, paper, rubber and silicone that survive into the melt either char at the die or pass through as black specks. Removing them early protects the melt filter and reduces odor, because those materials no longer spend minutes at high temperature. A belt melt filter downstream then handles the remaining fine solids with a continuous belt movement rather than a batch screen change that interrupts pressure.
9. Extrusion: Low Shear Melting and Temperature Windows
Screw and barrel design for fiber filled feed
A recycling extruder for WPC scrap uses a 100 to 150 millimeter screw with a length to diameter ratio in the 30 to 42 range, a low compression ratio and a mixing section placed after the melting zone. High shear is the enemy because it grinds wood fiber into dust, raises melt temperature and generates fines that clog the filter. Barrel zones are typically set from 150 to 190 degrees Celsius, with the melt kept below the point where wood darkens. The rigid flake equipment family offered by Wanplas spans 90 to 185 millimeter screws with outputs from 110 to 1,200 kilograms per hour and installed power from 110 to 380 kilowatts, giving a clear capacity ladder for a project.
Output classes and what they cost
A 90 millimeter line at 110 to 180 kilograms per hour suits a furniture maker recovering its own trim; a 130 millimeter line at 450 to 600 kilograms per hour suits a regional collector; a 185 millimeter line at 800 to 1,200 kilograms per hour suits a merchant plant. Installed power rises from 110 to 380 kilowatts across that range, and labor goes from one or two operators to two or four. Screw speed is normally controlled in the 10 to 150 revolutions per minute band, with lower speeds preferred for high fiber loads because they protect the fiber length.
Mixing and the second chance for the interface
Fresh coupling agent is added in the melting zone or through a side feeder so that it can react with the wood surface before the pellet is cut. A dispersive mixing section breaks up pigment agglomerates, while a distributive section spreads the coupling agent without over-shearing the fiber. The goal is a pellet whose melt flow index sits inside a narrow band, because the customer will run it on the same die that made the original board. Wanplas recommends a small side feeder with its own gravimetric dosing when the recycler plans to run several wood contents in one week.
10. Melt Filtration and Vacuum Degassing
Why a single screen changer is not enough
A WPC melt carries charred wood, paint flakes, rubber fragments and fine grit. A conventional screen changer catches them but the differential pressure climbs quickly and the operator has to change screens, interrupting output. A continuous belt melt filter with a filter area around 570 square centimeters and a capacity near 900 to 1,200 kilograms per hour moves a clean section of screen into the melt without stopping, while a backflush filter handles the finer solids downstream. The two stage approach costs 70,000 to 200,000 US dollars but stabilizes pressure and protects the pelletizer from a sudden surge of contamination.
Three vacuum stages and what each removes
The first vacuum vent at the start of melting pulls out free moisture and trapped air. The second, placed after filtration and mixing, removes water vapor released from wood fiber and the light volatile compounds from degraded coatings. The third, applied just before the die, strips the remaining odor compounds and prevents bubbles in the strand. Each stage needs its own condenser and a vacuum pump sized for water load rather than air alone. A triple package costs 35,000 to 100,000 US dollars and is the difference between a pellet that smells of old furniture and one that can be sold into a new product.
11. Pelletizing, Cooling and Pellet Quality
Water ring hot face versus strand cutting
Water ring hot face pelletizing is the usual choice for WPC recyclate because the pellets are cut at the die and carried away by circulating water, which prevents sticking when the melt contains high fiber loading. Strand pelletizing is simpler and costs less, but a strand filled with wood fiber is brittle and breaks between the die and the cutter when the formulation is dry. A water ring system for 1,000 kilograms per hour costs 45,000 to 150,000 US dollars including the centrifuge and classifier; a strand system at the same output may cost less than half. Plants running a single stable PE WPC grade can choose strand, while plants switching between PE, PP and PVC grades need the flexibility of hot face cutting.
Pellet size, moisture and bulk density
The practical target for recycled WPC pellets is a cylinder around 3 by 3 millimeters, with moisture between 1 and 2 percent and a stacking density of 0.5 to 0.8 grams per cubic centimeter. Pellets that are too long bridge in the customer’s feeder; pellets that are too short carry excess surface water and stick in the bag. Wood filled pellets cool faster than pure plastic, so the water temperature and residence time in the centrifuge have to be tuned together. A classifier after the dryer removes fines and doubles, and the rejected fraction should be fed back to the extruder rather than sold.
Packing and storage
Recycled WPC pellets absorb moisture again if stored in a humid warehouse, so they should be packed in lined bags or big bags with a desiccant when the journey takes more than a week. A 25 kilogram bag is convenient for a furniture plant adding recyclate to a virgin blend, while a 1,000 kilogram big bag suits an extrusion line running a high recycled content. Each package should carry batch, polymer family, wood content, melt flow index and moisture. Without that information the customer cannot set a recipe, and the pellet will be treated as a low grade filler rather than a controlled compound.
12. Additives and Recompounding Strategy
Restoring the wood plastic interface
Fresh coupling agent at 1.5 to 4 percent of compound weight restores adhesion between recycled wood fiber and the polymer. Maleated polyethylene is used for polyethylene based scrap and maleated polypropylene for polypropylene based scrap; using the wrong one gives a pellet that looks correct but fails in flexural testing. The coupling agent costs 2,800 to 5,500 US dollars per ton, so it adds roughly 0.006 to 0.022 US dollars per kilogram of finished pellet. That is a small price for recovering most of the stiffness that the first service life consumed.
Stabilizers, color and odor control
A fresh ultraviolet stabilizer package is needed when the recycled pellet will be used outdoors again, adding 0.004 to 0.012 US dollars per kilogram. Color is a commercial decision: dark browns and greys absorb variation in the incoming scrap, while light colors force the recycler to sort by color and limit the feed to one furniture line. Odor neutralizers cost 0.003 to 0.008 US dollars per kilogram but cannot replace proper degassing; they polish a pellet that is already clean. Wanplas recommends starting with the minimum additive package and adding only where a measured test shows a gap.
13. Quality Control and Performance Testing
Tests that protect the customer relationship
A recycled WPC pellet is sold on numbers, not appearance. The buyer wants a melt flow index close to the grade originally used, a known ash content that reveals the fiber fraction, low moisture and no hard particles that could block a die. The table lists eight tests used in a WPC reprocessing plant with an indicative target and the cost of the equipment needed to run it.
| Test | Typical target | Setup cost in US dollars |
|---|---|---|
| Moisture by loss on drying | 1 – 2 percent in pellet | 1,500 – 5,000 |
| Melt flow index | Within agreed grade band | 6,000 – 18,000 |
| Ash by combustion | Matches declared wood content | 3,000 – 9,000 |
| Bulk density | 0.5 – 0.8 g per cubic cm | 800 – 2,500 |
| Pellet size distribution | 90 percent within 2 – 4 mm | 1,000 – 4,000 |
| Black speck count | No particle above 100 microns | 8,000 – 25,000 |
| Metal contamination | No detectable ferrous fragment | Included in detector |
| Flexural test on test bar | Within customer grade band | 8,000 – 22,000 |
Sampling and lot records
Sampling happens at three points: incoming scrap, dried flake and finished pellet. Incoming sampling sets the batch grade, dried flake sampling confirms the process can run it, and pellet sampling decides whether the lot can be sold. A laboratory budget of 30,000 to 80,000 US dollars covers the full set, and the annual consumables are typically 4,000 to 12,000. A single customer claim on a contaminated lot can exceed the annual lab budget, which makes the investment straightforward.
14. Process Parameters and the Cost of Deviation
The twelve values to control
WPC reprocessing has a narrow operating band because the polymer wants more heat and the fiber wants less. The table gives working windows for a polyethylene based WPC line at 500 to 1,000 kilograms per hour and the cost of drifting outside them. Values for polypropylene shift about 10 to 15 degrees Celsius higher, and PVC based scrap needs its own fully separate recipe and temperature profile.
| Parameter | Working window | Cost of deviation |
|---|---|---|
| Flake size | Below 13 mm | Bridging, surging and unmixed fiber |
| Feed moisture | At or below 2 percent | Porous strand and splay |
| Barrel zones | 150 – 190 degrees C | Wood darkening or unmelted polymer |
| Melt temperature at die | Below 200 degrees C | Char, odor and black specks |
| Screw speed | 10 – 150 rpm, low end preferred | Fiber damage and higher shear heat |
| Specific mechanical energy | Hold within recipe band | Melt index drift between lots |
| Filter differential pressure | Rise below agreed limit per hour | Screen blow or pellet contamination |
| Vacuum level | Full vacuum at each stage | Residual odor and bubbles |
| Coupling agent dosing | 1.5 – 4 percent | Weak interface and low flexural strength |
| Die pressure | Stable within narrow band | Pellet size scatter and strand breaks |
| Water ring temperature | Controlled for shape retention | Tails, doubles or sticking pellets |
| Pellet moisture | 1 – 2 percent | Blistering at the customer’s die |
Storing and using the windows
Wanplas recommends storing each accepted recipe with its screw speed, temperature profile, screen differential and additive dosing, then calling it up rather than retyping values. A rising filter pressure at constant output is usually a feed sorting problem rather than a filter problem, and the right response is to check the incoming batch. Operators should log every override with a reason so that a repeated correction can be turned into a revised recipe.
15. Dust, Odor, Fire and Environmental Controls
Dust and fire prevention
Wood plastic dust is combustible and abrasive, so the shredder, granulator and dryer need local extraction, spark detection and a dust collector placed outside the main production hall. Floors and beams should be cleaned on a schedule rather than when visible, because a fine layer suspended in air is the real hazard. A dust system for a 1,000 kilogram per hour line costs 40,000 to 120,000 US dollars and is a condition of operation in most industrial permits.
Wash water and odor
Wash water carries soil, fiber and small amounts of coating residue, and it needs settling, filtration and a closed loop where the local rules allow reuse. A compact treatment package costs 50,000 to 150,000 US dollars. Process odor comes mainly from overheated wood and degraded coatings, so temperature control and early degassing solve more of it than masking agents. Exhaust from the dryer and the vacuum condensers should be filtered before discharge.
16. Output, Energy, Unit Cost and Payback
From nominal capacity to saleable pellet
A 1,000 kilogram per hour line does not deliver 1,000 kilograms of pellet every hour. Sorting losses, fines, wash sludge, screen solids and grade changes reduce the yield to 78 to 88 percent for mixed WPC furniture scrap, and a cleaner single-model stream can reach 90 percent. At 6,000 operating hours, a 1,000 kilogram per hour plant produces 4,700 to 5,300 tons of saleable pellet a year. Tracking each loss stream separately tells the operator whether the problem is upstream sorting or melt filtration.
Unit cost and pellet price
Collected WPC scrap costs 80 to 220 US dollars per ton at the gate, with clean single polymer furniture offcuts at the upper end. Washing, drying and labor add roughly 0.09 to 0.20 US dollars per kilogram, energy adds 0.05 to 0.10, additives 0.02 to 0.05, and plant overhead and packaging another 0.04 to 0.08. Delivered cost lands near 0.30 to 0.55 US dollars per kilogram, while consistent recycled WPC compound sells for 0.45 to 0.85 depending on polymer family and wood content. The margin is real but narrow enough that yield and uptime decide profitability.
Investment and payback
A complete 1,000 kilogram per hour plant including installation and water treatment comes to roughly 1.0 to 1.8 million US dollars. At 5,000 tons a year and a contribution near 0.18 US dollars per kilogram, annual contribution is about 0.90 million US dollars, giving a payback of 14 to 24 months. A 300 to 500 kilogram per hour captive line can pay back in 12 to 18 months when it displaces purchased compound, while a poorly sorted merchant plant can take more than three years. Feed quality and a contracted offtake matter more than the screw diameter.
17. Wanplas Equipment Recommendation and Buying Checklist
Which Wanplas equipment fits WPC scrap
Wanplas supplies the full chain for this application. The rigid flake recycling and pelletizing family covers 90 to 185 millimeter screws with 110 to 1,200 kilograms per hour output, 110 to 380 kilowatts of installed power and one to four operators, and the stated feed requirement is flake below 13 millimeters with moisture at or below 2 percent. The new generation recycling line adds a preconditioning unit, a belt melt filter with 570 square centimeters of area and triple degassing at 900 to 1,200 kilograms per hour. For WPC furniture scrap, Wanplas recommends the preconditioning and dual filtration route because it removes cellulose and rubber before they overheat.
What to settle before the order
Define the polymer families accepted, the maximum wood content, the incoming moisture, the contamination level and the target pellet specification in writing. Then confirm the separator package, the dryer size, the filter layout, the number of vacuum stages and the additive feeders. A line bought for clean rigid flake will make pellets from WPC scrap, but the filter will clog and the pellets will smell. Wanplas recommends running a representative inbound load during acceptance rather than a clean test material.
Acceptance test and spare parts
Require a four hour run with the buyer’s own scrap, measurements of pellet moisture, melt flow index, ash content and black spec count, and a check of filter pressure rise per hour. Hold 10 percent of the machine price until the first commercial lot is accepted by the customer. A spare knife set, a screen belt, a vacuum pump seal kit and a spare granulator screen should be included, because each can stop a line for days when it fails.
Frequently Asked Questions
How much does a waste WPC recycling pelletizing line cost?
A compact 300 to 500 kilogram per hour plant costs 150,000 to 350,000 US dollars. A complete 1,000 kilogram per hour line with washing, drying, preconditioning and dual filtration costs 450,000 to 1,600,000 US dollars, with installation and water treatment adding 90,000 to 260,000.
Can PE, PP and PVC WPC scrap be processed together?
No. Polyethylene, polypropylene and PVC WPC need separate campaigns and separate temperature profiles. A single PVC profile in a polyethylene batch can degrade the whole lot, so sorting at intake is more important than any downstream filtration.
What moisture level is required before extrusion?
Feed moisture should be at or below 2 percent, and finished pellets normally land between 1 and 2 percent. Wood fiber holds water internally, so a thermal dryer with adequate residence time is needed after the centrifuge.
Why does WPC scrap need a coupling agent again?
The first melt and the years of service consume part of the interface between wood and polymer. Adding 1.5 to 4 percent fresh maleated polyolefin restores stiffness and impact strength, at a cost of roughly 0.006 to 0.022 US dollars per kilogram of pellet.
What pellet size is typical for recycled WPC?
A cylinder around 3 by 3 millimeters with a stacking density of 0.5 to 0.8 grams per cubic centimeter is the usual target. Water ring hot face cutting is preferred when fiber loading is high or several grades share the line.
How much wood fiber survives reprocessing?
Some fiber shortening is unavoidable. Each grinding and melting pass reduces fiber length, which lowers the reinforcing effect, so recycled WPC pellet is normally directed to less demanding parts than the original board unless virgin fiber is added.
What causes black specks in recycled WPC pellets?
Charred wood, rubber gaskets, silicone sealant and paint heated beyond the fiber limit. Removing them early in preconditioning and using a continuous belt melt filter is more effective than relying on a single screen changer.
What should the acceptance test cover?
Run four hours with the buyer’s scrap, then check pellet moisture, melt flow index, ash content, black spec count and filter pressure rise per hour. Hold 10 percent of the price until the first commercial lot passes at the customer’s plant.
Conclusion
A waste WPC recycling pelletizing line is a sorting and moisture control problem as much as an extrusion problem. The polymer families must be kept apart, wood fiber must be protected from excess heat, and contamination has to be removed before the screw breaks it into particles that no filter can catch.
The economics depend on yield and on a contracted outlet. Collected scrap at 80 to 220 US dollars per ton can become a pellet worth 0.45 to 0.85 US dollars per kilogram, but only when drying, filtration and degassing hold the product inside a narrow specification. A line that saves on those sections will spend the saving on rejected lots.
Wanplas recommends a preconditioning and dual filtration configuration for furniture scrap, built around a 100 to 150 millimeter recycling extruder with triple vacuum degassing and water ring pelletizing. Defined that way, the line turns a difficult waste stream into a repeatable secondary compound for a new generation of WPC products.

