Contents
1. What a PVC Window Door Profile Line With Online Finishing Is and Who Buys One
The machine and the product it makes
A PVC window door profile extrusion line with laminating and punching online is a continuous system that turns a dry blended rigid polyvinyl chloride compound into a finished, decorated and pre-drilled length of window or door profile. The chain begins at the mixer and feeder, passes through a conical twin-screw extruder and a profile die, then through a vacuum calibration table, a cooling trough, a haul-off and a flying cut-off saw. The distinguishing feature is what happens after the cut. Instead of stacking a bare extrusion for a separate finishing department, the line applies a decorative or protective film and cuts hardware slots, drainage openings and assembly holes while the profile is still traveling at line speed.
Three buyer groups and their real requirements
The first buyer is an integrated window systems house that extrudes its own main profiles and wants to capture the margin that otherwise goes to a coating contractor. The second is a profile extruder supplying fabricators, whose customers increasingly demand a ready to decorate surface and pre-punched hardware positions. The third is a building products group running several system depths and many colors, where the deciding factor is how quickly the line changes from one section and one film to another. All three groups buy the same nominal machine, but they value different things: the first wants low cost per meter, the second wants repeatable hole position, and the third wants short changeover.
2. Where the Value of Online Laminating and Punching Comes From
The cost of doing finishing offline
In a conventional plant the extrusion leaves the cooling trough, is cut to length, stacked on a cart, moved to a finishing area, re-handled onto a work bench, filmed or wrapped by hand, drilled with a jig, and stacked again. Each transfer consumes labor and creates an opportunity to damage the visible face. Offline punching also needs a jig per profile system, and the jig has to be reset whenever the section changes. When volume is high enough, the labor and the rework bill exceed the cost of adding the finishing stations to the line, which is the economic reason for integrating them.
Synchronization is the whole trick
An online station does not simply sit next to the extruder; it has to follow the profile. The flying saw, the film applicator and the punching head all take their position signal from an encoder that measures actual line travel, not from motor speed. A punch fired at the wrong instant lands millimeters away from the hardware position, and a film applied under the wrong tension wrinkles at the corners. Wanplas treats encoder resolution, response time and the mechanical stiffness of the moving carriage as one system, because a fast controller cannot correct a frame that flexes under acceleration.
3. Profile Families, System Depths and Cross Sections
Main frames, sashes and auxiliary sections
A window system is a family of sections rather than a single shape. The main frame carries the glass and the hardware, the sash holds the sealed unit, and a set of auxiliary profiles covers the glazing bead, the sill, the mullion, the shutter groove and the insect screen track. Each has a different wall thickness and a different cooling behavior. The main frame is usually the heaviest section and sets the line speed, while a thin glazing bead can run faster but is more prone to warp. A line specified only for the main frame often struggles when the plant wants to sell the whole system.
System depth and weight per meter
Window systems are described by the depth of the frame, commonly between 50 and 90 millimeters, with deeper sections carrying more glass and better insulation. A deeper profile is not simply a wider version of the same shape; it has more internal chambers, more material and a longer cooling time. Wall thickness typically falls between 1.8 and 3.0 millimeters for rigid window profiles, with the outer wall slightly heavier than the internal webs. Weight per meter is the number that drives both material cost and the maximum practical output of a given extruder.
Section comparison
The table below shows representative sections and the way their geometry changes production choices. Figures are typical design ranges rather than a guarantee for any one system, and the buyer should replace them with the actual drawing before finalizing screw speed, die layout and calibration tooling.
| Profile type | System depth | Wall thickness | Weight per meter | Production note |
|---|---|---|---|---|
| Main frame | 60 to 88 mm | 2.0 to 3.0 mm | 1.0 to 1.8 kg | Sets line speed; needs strong calibration |
| Sash | 60 to 80 mm | 1.8 to 2.6 mm | 0.8 to 1.4 kg | Hardware slots demand accurate punching |
| Glazing bead | 10 to 20 mm | 1.2 to 1.8 mm | 0.08 to 0.18 kg | Fast but warp sensitive; small die |
| Sill and mullion | 60 to 100 mm | 2.2 to 3.0 mm | 1.2 to 2.2 kg | Drainage holes and longer cooling |
4. Rigid PVC Formulation, Heat Stability and Compound Cost
Resin, stabilizer and modifier package
Rigid window profile starts with suspension grade PVC resin with a K value around 65 to 68, which gives the stiffness needed for a load bearing frame while still flowing through a complex die. Around the resin sits a heat stabilizer, usually a calcium zinc system in modern formulations, a processing aid based on acrylic chemistry, an impact modifier, a lubricant package and a mineral filler. Outdoor white profiles add a substantial titanium dioxide loading for ultraviolet protection. The exact balance is a compromise: more filler lowers cost but reduces impact strength, and more impact modifier improves toughness but raises melt viscosity and die pressure.
What a ton of compound costs
A representative rigid profile compound lands between 780 and 950 US dollars per metric ton delivered to the hopper, with the range explained mostly by resin price, filler loading and titanium dioxide content. A high white outdoor formulation can sit above that band, while a filled interior section can sit below it. Rework is normally limited to a controlled percentage, because repeated heat history reduces stability and shows up as discoloration on the visible face. A buyer should calculate material cost from the density of the actual compound and the measured weight per meter, not from a catalog price per ton.
5. Complete Line Architecture and Equipment Price List
The chain from mixer to pallet
A complete line includes the mixer, the material handling, the extruder, the die, the calibration table, the cooling trough, the haul-off, the cut-off saw, the film unwind and applicator, the punching unit, the discharge table and the control system. Each zone is sized from the widest profile and the heaviest section the plant intends to run. A line built for a 180 millimeter maximum product width is a different investment from one built for 600 millimeters, even if the screw diameter looks similar on paper, because the die, the calibration table and the downstream rollers all scale with width.
Equipment price list
The figures below are delivered equipment prices in US dollars for a mid range line handling profiles up to 300 millimeters wide. Freight, sea packing, foundation work, installation and training are separate. A buyer should read the range as a design choice rather than a discount opportunity: a narrow range usually means the item is a fixed specification, while a wide one means the configuration changes the price substantially.
| Line section | Typical price in US dollars |
|---|---|
| High speed hot and cold mixer package | 25,000 to 70,000 |
| Conical twin-screw extruder and drive | 110,000 to 280,000 |
| Profile die for one system family | 18,000 to 65,000 |
| Vacuum calibration table | 30,000 to 85,000 |
| Cooling trough and water system | 16,000 to 48,000 |
| Haul-off unit | 20,000 to 55,000 |
| Flying cut-off saw and dust collection | 22,000 to 60,000 |
| Film unwind, adhesive and laminating head | 45,000 to 140,000 |
| Servo tracked punching unit with tooling | 55,000 to 180,000 |
| Discharge table and pallet station | 9,000 to 26,000 |
| Control system, encoders and remote access | 24,000 to 70,000 |
| Spare parts and first wear kit | 12,000 to 35,000 |
What the total means in practice
Adding the midpoint of each line item gives roughly 0.42 million US dollars, and a realistic project budget adds 40,000 to 90,000 US dollars for foundations, installation, commissioning and operator training. The first set of dies for a full window system is usually a separate order and can add 60,000 to 180,000 US dollars depending on how many sections are included. A buyer who needs only a bare extrusion line can defer the laminating and punching stations, but adding them later means re-engineering the downstream frame and losing production time during installation.
6. Conical Twin-Screw Extruder and Profile Die
Why rigid PVC needs a conical twin screw
Rigid PVC is heat sensitive and cannot tolerate the long residence time of a general purpose single screw. A conical twin-screw extruder feeds the dry blend at the wide end of the screws and compresses it as the diameter decreases, which gently heats the material through barrel conduction and shear. The result is a stable melt at a relatively low temperature, with good devolatilization through the hopper. The extruder powers quoted on the Wanplas profile line are 22, 37 and 55 kilowatts across the product width range, and the buyer should match the drive to the heaviest section rather than to the average one.
Die design and flow balance
A profile die is a flow distribution problem. The melt entering from the extruder has to be split between thick walls, thin webs and corners that cool at different rates. A badly balanced die makes the operator slow the line until the thinnest wall fills, which wastes the capacity of the whole machine. Die designers adjust land length, entry angle and local restriction until the exit velocity is even across the section. Die temperature is controlled zone by zone, and a difference of a few degrees between two zones can move material from one wall to another enough to fail the drawing tolerance.
Matching the screw and die to product width
Wanplas profile lines are specified by maximum product width: 180, 240, 300 and 600 millimeters. The smallest configuration uses a 22 kilowatt extruder and about 18 meters of line length, while the widest uses 55 kilowatts and about 25 meters. Cooling water demand rises from 5 to 10 cubic meters per hour and compressed air from 0.2 to 0.4 cubic meters per minute across the same range. These numbers are useful as a sanity check during negotiation: if a supplier quotes a wide line with a small drive and short cooling, the line will either run slowly or produce a profile that bends after cutting.
7. Vacuum Calibration and Cooling: Where Geometry Is Set
How a vacuum calibration table works
The extrudate leaves the die soft and slightly oversized. It enters a calibration sleeve whose internal cavity is the negative of the finished profile, and vacuum applied through small holes pulls the soft outer wall against that cavity. This is the step that fixes the external dimensions, the corner radii and the surface finish; the die shapes the melt, but the calibrator defines the saleable geometry. The sleeve is water cooled and usually split into several vacuum zones so the operator can tune suction from the entry to the exit. Too much vacuum at the entry drags the melt and thins one wall; too little leaves the profile loose and moving inside the sleeve.
Water temperature and the cooling length problem
Cooling is a heat removal calculation, not a matter of making the trough as long as possible. Rigid PVC gives up heat slowly because it is a poor conductor, and the internal webs stay hot longer than the outer skin. Water temperature is normally held in a controlled band, and the profile passes through several zones so the drop is gradual. A line that quenches too fast locks stress into the walls, and the profile bends later when it is cut or stored in the sun. This is why the longer lines in the width range are not simply bigger machines; the extra length is where the section loses its residual heat before downstream finishing touches it.
8. Haul-Off, Length Control and Cutting
Haul-off traction and surface marking
The haul-off pulls the profile through the calibrator and cooling trough at a controlled speed. Traction must be firm enough to overcome the drag of the vacuum sleeve but gentle enough not to crush a hollow section or leave tracks on a face that will later be laminated. Rubber padded caterpillar tracks are common for larger profiles, while smaller beads may use rollers. Wear on the pads changes the effective pull and shows up as a slow drift in wall thickness, so pad condition belongs on the maintenance list rather than being treated as a consumable nobody watches.
Length measurement and the flying saw
Window profiles are cut to standard stock lengths, and the tolerance on that length matters because the fabricator nests several pieces into a frame. A flying saw travels with the profile while the blade advances, then returns for the next cut. Position is taken from a measuring wheel or encoder on the profile itself, which avoids the error that accumulates when a control system assumes the haul-off speed is exact. Dust extraction at the saw is not optional on a line that runs laminated sections later, because fine PVC dust stuck to the face will show through the film as a bright speck.
9. Online Laminating: Film, Adhesive and Application
Choosing the film for the application
The film applied online is chosen for decoration, protection or both. Printed polyvinyl chloride films with a wood grain, stone or solid color are common for interior window systems, while a clear polyethylene or polyester film protects a profile during transport and construction. The film has to match the service environment: an exterior dark color absorbs more heat, and a film with poor ultraviolet stability will fade or peel long before the PVC itself fails. Thickness is usually measured in microns, and the buyer should specify both the film and the adhesive system rather than accepting a generic laminating unit.
Adhesive, heat and nip pressure
Application works by warming the film and the profile face, activating the adhesive and pressing the two together through a nip roll. Pre coated films need heat only; other systems add a liquid or hot melt adhesive at the unwind. The control variables are temperature, nip pressure and web tension. Too little heat gives poor adhesion that fails in a tape test, too much heat distorts the film or softens the profile face, and uneven pressure leaves bubbles along the chamber walls where the surface is not flat. The applicator is normally positioned after the profile has cooled and been cut, so a defective length can be rejected before it enters the finishing stream.
10. Online Punching: Hardware Slots, Drainage and Assembly Holes
What is actually punched
A window profile carries a surprising number of openings. Hardware slots receive the lock, handle and hinge components; drainage slots let water escape from the glazing chamber; pressure equalization holes connect chambers to the outside; and assembly holes locate screws and reinforcements. Cutting these online removes a full bench operation from the fabricator and, more importantly, guarantees that the position follows the same datum as the extrusion. The openings are usually punched rather than drilled because a shaped punch produces a clean edge in one stroke and holds its position better over a long campaign.
Servo tracking and position accuracy
The punching head rides on a carriage that accelerates to line speed, fires while matched to the moving profile, and returns to the start position. This is why the unit is servo driven and synchronized to the same encoder as the saw and the laminator. Accuracy depends on the response of the servo, the stiffness of the carriage and the accuracy of the encoder signal. A buyer should specify the allowable hole position error over a full stock length and ask for a measured result at production speed, not a figure taken from a static test. Warm profiles also move slightly under the punch, so tooling must support the wall from behind.
Burr control and tool life
Punch tools wear at the cutting edge, and the first sign is usually a burr on the inner wall rather than a visible defect on the face. A burr interferes with hardware fitting and can lift the laminated film if the punching station is placed after lamination. Most lines therefore punch before the film is applied, or use a local vacuum to remove chips before the nip. Tool steel grade, clearance between punch and die and the filler content of the compound all affect life. Wanplas recommends keeping a complete spare punch set for the highest volume section, because a single worn slot can stop acceptance at the fabricator even when the rest of the line is running perfectly.
11. Coordinated Line Control and Grade Changeover
One shared position signal for the whole line
The extrusion, cooling, cutting, laminating and punching zones can be controlled separately, but they must share one measure of profile travel. A line that uses motor speed as a proxy for line speed will drift as the haul-off pad wears or the profile slips. Wanplas uses encoder feedback from the moving profile as the common signal, so the saw, the film applicator and the punching carriage all react to the same physical event. The controller stores the recipe for each section, including die temperatures, haul-off speed, film tension and hole positions, and recalls it at the next changeover.
How long a real changeover takes
Changing from one profile system to another involves heating the new die, pulling the old profile out of the calibrator, threading the new section through the cooling trough and haul-off, setting the punch positions and splicing or replacing the film roll. On a well organized line this takes roughly 45 to 120 minutes; on a line where every setting is manual it can take half a shift. The cost is not only lost production but the transition material generated while the gauges settle. Recipe storage, quick change tooling and a prepared film splice all reduce that loss, and they pay back fastest in plants running short batches of many colors.
12. Quality Control and Performance Testing
Dimensional and appearance checks
Quality control starts with the section itself: wall thickness at defined points, external dimensions against the calibration sleeve, straightness over a stock length and the absence of sinks or voids at the corners. Appearance is checked on the visible face under controlled light, because a gloss difference that is invisible on the shop floor is obvious once a window is installed. For laminated profiles the check expands to film alignment, bubble count, edge coverage and color match between rolls. A single roll change can shift the shade enough to be visible on a completed frame.
Physical and performance tests
Rigid window profile is tested for impact resistance, heat reversion, dimensional stability under heat and, for exterior grades, resistance to weathering. The film adds its own tests: adhesion by peel, resistance to rubbing, and behavior after heat aging. Punched openings are checked for position, edge quality and the absence of cracks that could spread from the cut. Not every test runs on every length; most plants use a defined first article check, a periodic sample and a full test campaign when the formulation, die or film supplier changes.
13. Process Parameters and the Cost of Deviation
The windows that matter
A profile line has many setpoints, but only a handful drive cost and quality at the same time. Barrel and die temperatures control melt viscosity and surface finish. Screw speed and haul-off speed together determine output and wall thickness. Calibration vacuum fixes external dimensions, and cooling water temperature fixes how much stress remains in the section. On the finishing side, film temperature and nip pressure control adhesion, while punch position and carriage acceleration control hole accuracy. A deviation in any one of these does not stay in its own zone; a cooling problem shows up as a film defect two stations later.
Parameter table
The table gives representative operating windows for a rigid PVC window profile line with online finishing. The figures are starting points for trials, not settings for a specific compound or die, and the buyer should refine them during acceptance with the actual formulation and section drawings.
| Parameter | Typical window | Cost of deviation |
|---|---|---|
| Barrel temperature | 160 to 190 degrees Celsius | Yellowing or unmelted particles |
| Die temperature | 185 to 205 degrees Celsius | Poor surface or uneven walls |
| Melt pressure | Stable within a narrow band | Dimensional drift and scrap |
| Extruder power | 22, 37 or 55 kW by width | Undersizing limits output |
| Calibration vacuum | Set by section and sleeve | Sink marks or wall thinning |
| Cooling water | 5 to 10 cubic meters per hour | Warpage after cutting |
| Compressed air | 0.2 to 0.4 cubic meters per minute | Punch and saw faults |
| Line length | 18 to 25 meters by width | Short lines limit speed |
| Film application temperature | Set by adhesive system | Peeling or film distortion |
| Nip pressure | Even across the face | Bubbles at chamber walls |
| Punch carriage speed | Matched to haul-off | Hole position error |
14. Surface Quality and Scrap Control
The defects buyers notice first
Window profile is judged by its visible face, so surface defects cost more than their size suggests. Yellow streaks come from local overheating or poor stabilizer dispersion. Flow lines appear when the melt front in the die is not welded evenly. Shark skin and matte patches indicate that the melt is leaving the die too fast for the temperature. A laminated profile hides some of these defects but not all: a raised flow line can print through the film, and a gloss difference changes the way the color reads. The finishing line therefore raises the standard required at the die rather than lowering it.
Where scrap is created and how to reduce it
Scrap on a profile line is concentrated in three places: start up after a die or color change, transition material during a grade change, and off specification output that is discovered after finishing. The first two are unavoidable but controllable through recipe storage and disciplined changeover. The third is the expensive one, because a laminated and punched length carries film, tooling time and labor in addition to the compound. A plant that detects a dimensional drift at the calibrator and stops before the laminator saves the whole downstream value. This is the practical reason to place measurement close to the point where the defect is created.
15. Output, Energy and Line Efficiency
What determines real output
Catalog output for a profile line is usually given in kilograms per hour for a baseline section, which makes two lines look comparable when they are not. Real output depends on the heaviest section the plant sells, the cooling capacity available and the speed at which the punching carriage can follow the profile. A thin glazing bead may run fast enough to overwhelm the finishing stations, while a deep main frame may be limited by heat removal long before the extruder reaches its rating. Wanplas recommends sizing the line from a weighted average of the intended product mix, then checking the peak section against the cooling length.
Energy and water costs
The 22 to 55 kilowatt extruder drive is the largest electrical load, but the mixers, cooling water pumps, vacuum pumps, haul-off, saw and finishing stations add a substantial share. A mid size profile line typically draws 90 to 180 kilowatts at full production, and compressed air demand of 0.2 to 0.4 cubic meters per minute adds the cost of a compressor that is often underestimated. Water consumption of 5 to 10 cubic meters per hour is largely recirculated, so the real cost is pumping and heat rejection rather than makeup water. A plant with poor chiller capacity will lose output in summer no matter how good the extruder is.
16. Cost per Meter, Market Price and Payback
Building the cost of one meter
Start with the compound. A main frame weighing 1.2 kilograms per meter at 850 US dollars per ton carries about 1.02 US dollars of material per meter. A printed decorative film applied to one or more faces adds roughly 0.20 to 0.60 US dollars per meter depending on width and film type, and punching adds 0.03 to 0.10 US dollars in tooling wear and handling. Energy at a typical line speed contributes 0.04 to 0.09 US dollars, and labor plus overhead adds another 0.10 to 0.20. A fully finished main profile therefore lands near 1.40 to 2.00 US dollars per meter of conversion cost before margin, while a bare white profile sits much lower.
Price benchmarks and the finishing premium
Bare rigid window profile is sold close to material plus conversion, and competition keeps the premium thin. A laminated, pre-punched profile is quoted as a finished component, with selling prices commonly 25 to 60 percent above the equivalent bare section for the same system. The premium is not only the film; it is the removal of a finishing operation at the fabricator and the reduction in rejected frames caused by misplaced hardware slots. A plant that can document hole position accuracy and film adhesion in its quotation is selling a specification, which is a much stronger position than selling kilograms.
Investment and payback
A complete line as described in the equipment table represents roughly 0.42 million US dollars in equipment, or 0.46 to 0.55 million with installation, training and the first spare kit. At a converted contribution of 0.15 to 0.35 US dollars per finished meter and two shift operation, annual production of four to six million meters gives a payback of roughly 18 to 34 months. A plant already paying a contract finisher will recover the finishing investment faster, sometimes inside a year. The sensitivity is not the extruder output but the utilization of the laminating and punching stations, which is why Wanplas recommends securing an order book for finished profiles before specifying the widest line.
17. Wanplas Equipment Recommendation and Buying Checklist
Which Wanplas equipment fits this application
Wanplas supplies the profile extrusion family that matches this task, with maximum product widths of 180, 240, 300 and 600 millimeters, extrusion power of 22, 37 and 55 kilowatts, line lengths from 18 to 25 meters, cooling water demand of 5 to 10 cubic meters per hour and compressed air of 0.2 to 0.4 cubic meters per minute. For a window and door plant the 240 or 300 millimeter configuration normally covers the full system family, including frames, sashes and auxiliary sections. The online laminating head and the servo tracked punching unit are specified together with the line, so the encoder, frame length and discharge table are designed as one system rather than retrofitted later.
What to settle before signing
Define the system depths, the heaviest section, the wall thickness range, the film types and the full list of punch positions before the order is placed. Then confirm the die scope, the number of calibration sleeves, the adhesive system, the unwind positions, the spare punch sets and the recipe package. A supplier may quote a lower price for a line that handles only one main frame, and that line will struggle the moment the plant adds a sill or a glazing bead. Wanplas recommends specifying the product family, not just the first order, because the die and cooling layout are the parts that are expensive to change later.
Acceptance test and spare parts
Require a four hour continuous run with the buyer’s own compound and drawing, including at least one film change and one punch position change. Measure wall thickness, external dimensions, straightness after a dwell period, film adhesion on the face and inside corner, and hole position over a full stock length. Hold 10 percent of the machine price until the first commercial lot is accepted by the fabricator. Include a spare set of punch tools, a spare saw blade, calibration sleeve seals, nip roll covers and a set of heated zone components, because each of these can stop a finishing line for days when it wears out.
Frequently Asked Questions
How much does a PVC window profile line with laminating and punching cost?
A line for profiles up to 300 millimeters wide typically costs 380,000 to 620,000 US dollars including the laminating head and servo punching unit. A wider 600 millimeter configuration with a full die set for a complete window system can reach 900,000 US dollars, with installation and training adding 40,000 to 90,000.
Can the film be applied before the holes are punched?
It can, but it is rarely the better order. Punching after lamination exposes the film edge to chips and burrs, and a worn tool can lift the film around a slot. Most lines cut the holes first, remove the chips, then laminate, so the visible face stays intact and the punch wear does not affect the finish.
Why does rigid PVC need a conical twin-screw extruder?
Rigid PVC is heat sensitive and needs a short, gentle melting path. A conical twin screw compresses the dry blend gradually and keeps residence time low, which protects the stabilizer system and gives a steady melt through a complex profile die. A general purpose single screw will overheat the compound at the same output.
What line length is needed for window profiles?
Wanplas profile lines run from 18 to 25 meters depending on maximum product width. A 180 millimeter line is about 18 meters long, while a 600 millimeter line reaches about 25 meters. The extra length is cooling capacity, which determines how fast a deep main frame can run without bending after the cut.
How accurate can online punching be?
A well set up servo carriage working from a profile encoder holds hole positions within a fraction of a millimeter over a stock length when the line runs at steady speed. Accuracy depends on carriage stiffness and encoder quality as much as on the servo itself, so acceptance should be measured at production speed with the real section.
What causes film bubbles on a laminated profile?
Trapped air at a chamber wall, insufficient nip pressure, surface dust or moisture leaving the profile after application. The profile must be fully cooled and clean before the nip, and the applicator should use even pressure across the face. A dwell test at elevated temperature reveals bubbles that are not yet visible at the line.
How long does a profile changeover take?
With stored recipes and prepared tooling, 45 to 120 minutes is realistic for a change involving a new die, calibration sleeve and film roll. A color change on the same section is faster. The hidden cost is the transition material produced while wall thickness and film alignment settle, which is why recipe storage pays back quickly in short batch production.
What should an acceptance test cover?
Run four hours with the buyer’s compound and drawings, change the film and the punch positions at least once, then measure wall thickness, external dimensions, straightness after a dwell period, film adhesion and hole position over a full stock length. Hold part of the price until the fabricator accepts the first commercial lot.
Conclusion
A PVC window door profile line with laminating and punching online is a single position controlled system, not three machines placed next to each other. The extruder makes the section, the calibrator fixes the geometry, and the finishing stations add decoration and function while the profile is still moving. The value appears only when the saw, film applicator and punch carriage all follow the same encoder signal.
The economics favor a finished profile over a bare one. Compound at 780 to 950 US dollars per ton becomes a main profile near 1.02 US dollars of material per meter, and film plus punching add roughly 0.23 to 0.70 more. The finished section commands a 25 to 60 percent premium because it removes an entire finishing operation at the fabricator, and a 0.42 million US dollar line can pay back in 18 to 34 months when the finishing stations stay utilized.
Wanplas recommends a 240 or 300 millimeter configuration with 37 kilowatt extrusion power, an 18 to 25 meter line length and a servo tracked punching unit synchronized to the same encoder as the laminator. Defined around the whole profile family rather than the first order, the line turns a dry PVC blend into a decorated, pre-punched and directly usable window system component.

