Contents
1. What a Medical Pill Bottle Injection Blow Molding Machine Is and Who Buys One
The machine and the bottle it makes
A medical pill bottle injection blow molding machine is a three station rotary system that makes a small, rigid pharmaceutical container with a precisely formed neck in one continuous cycle. It first injects a molten polymer around a steel core rod to form a preform with a finished neck, then blows that warm preform against a cooled cavity to shape the body, and finally strips the bottle off the rod. The result is a clean, seamless container with no pinch weld at the base and no trimmed flash at the neck. For a pill bottle that must seal reliably and show whether it has been opened, that combination of a precise neck and a clean body is exactly what the process delivers.
Three buyer groups and their real requirements
The first buyer is a pharmaceutical packer that fills solid dose products and needs bottles whose neck dimensions hold tight enough for a high speed capping line. The second is a contract manufacturer that runs many bottle sizes and short campaigns, whose priority is fast mold changes and low purge loss between colors or resins. The third is a nutrition or supplement brand that wants a tamper evident, tamper resistant package with a premium appearance. All three depend on the neck, but for different reasons: the packer wants sealing consistency, the contract maker wants repeatable changeovers, and the brand wants a break band that looks and behaves correctly in the consumer’s hand.
2. Why Injection Blow Molding Wins for Pharmaceutical Bottles
The neck is the reason
In extrusion blow molding the parison is pinched closed and the neck is formed by the mold, which leaves a weld and flash that must be trimmed. In injection blow molding the neck is injected around a core rod before the body is blown, so its thread, sealing land and tamper band are formed under high pressure and held to a tight tolerance. That difference decides the process for a pill bottle. The closure is the most failure sensitive part of the package, and a neck that is oval, short on thread or inconsistent between cavities will fail at the capper rather than at the molding machine, where the fault is far more expensive to find.
Clean, seamless and trim free
Because the preform is injected and the bottle is blown inside a closed cavity, the part leaves the machine finished. There is no tail to cut, no pinch weld to inspect and no flash to remove. That matters in a pharmaceutical environment where loose plastic dust and open trim edges are unwelcome. The absence of a weld line also improves top load strength and makes the bottle easier to clean, which is why the process is standard for small containers where appearance and integrity both count. A converter moving from extrusion blow to injection blow usually sees the saving in reduced rejects rather than in faster cycle time.
Comparison with the other routes
The table shows how injection blow molding compares with the alternatives for a small pharmaceutical bottle. The figures are general design guidance, and the final choice depends on bottle volume, resin, closure type and annual quantity.
| Process | Neck precision | Trim and weld | Best fit |
|---|---|---|---|
| Injection blow molding | High, neck injected | No tail, no pinch weld | Pill bottles, samples, medical containers |
| Extrusion blow molding | Lower, neck blown | Tail and pinch weld | Large bottles, handles, low cost containers |
| Injection stretch blow molding | High with separate preform | No trim | Clear PET water and beverage bottles |
| Injection molding alone | Very high | No trim | Thick wall jars and closures |
3. The Three Station Process Step by Step
Injection station and preform
Dried resin is plasticized by a reciprocating screw and injected through a hot runner into a neck cavity and a body preform cavity that close around a temperature conditioned core rod. The neck fills first and is held under pressure while the preform body forms around the rod. The core rod is the critical tool here: it carries the internal shape of the neck and the starting wall of the body, and its temperature controls how much the material can stretch in the next station. Injection pressure, melt temperature and rod temperature together decide whether the thread is sharp and the wall is even.
Blow station and cooling
The core rod indexes to the blow station carrying the warm preform. Compressed air enters through the rod and expands the preform against a cooled bottle cavity, where the body takes its final shape and the tamper band is calibrated. The neck stays on the rod and is not blown, which is why its dimensions remain precise. Cooling time is set by the wall thickness and the resin, and it is usually the longest part of the cycle. A bottle that leaves the cavity too warm will shrink at the neck and distort on the conveyor, so the blow station is where dimensional stability is won or lost.
Stripping and takeout
At the third station a stripper plate pushes the finished bottle off the core rod and onto a conveyor or into a neck up chute. The bare rod returns to the injection station to be conditioned and reused. Because all three stations work at the same time on different sets of rods, one machine cycle produces one full set of bottles. The takeout must handle the bottle without marking the sealing land or tipping the tamper band, so neck up orientation and gentle guiding are part of the design rather than afterthoughts.
4. Tamper-Evident Neck Design and How the Break Band Works
What tamper evident means on a bottle
A tamper evident bottle shows that the closure has been opened. The usual mechanism is a thin break band below the thread, connected to the bottle by small bridges. When the cap is first twisted, the band stays on the neck while the cap moves up, and the bridges snap. The consumer sees a visible gap or a separated ring. The feature has to work every time and it has to resist casual attempts to reassemble it, which is why the band geometry, the bridge count and the cap engagement are designed together. On a pill bottle the same feature also supports child resistant closures that require a push and turn action.
Design details that decide reliability
The band is only a fraction of a millimeter thick in its weakest section, so injection filling and cooling must be even around the full circumference. A short shot or a weld at one bridge makes the band break early, while an overpacked bridge makes it too strong to snap cleanly. The gap between the band and the cap skirt has to be controlled so the cap can travel without rubbing yet leave a clear visual signal. Wanplas recommends proving the band on molded samples with the actual closure, because a neck that measures correctly on a gauge can still fail when a real cap is applied at line speed.
5. Bottle Sizes, Weights and Neck Dimensions
Volume ranges for solid dose products
Pharmaceutical solid dose bottles commonly run from a small 20 milliliter count container to a 500 or 1,000 milliliter family pack. The Wanplas injection blow platform covers product volumes from 2 to 1,000 milliliters, with maximum bottle height around 200 to 230 millimeters and diameter from 80 to 100 millimeters depending on machine size. That range covers the great majority of pill containers as well as sample and supplement bottles. The buyer should select from the actual bottle drawing, because a tall narrow bottle and a short wide bottle of the same volume behave very differently in blowing and cooling.
Wall thickness and weight per bottle
A 100 milliliter pill bottle in polypropylene typically weighs 12 to 18 grams with a wall around 0.6 to 0.9 millimeter, while a 300 milliliter bottle may weigh 25 to 40 grams. Wall thickness is set by top load and drop requirements rather than by volume alone, and the tamper band and thread area are usually heavier than the sidewall. Because resin is the largest single cost, a small reduction in wall thickness saves money across millions of bottles, but it has a floor. A bottle that passes a laboratory measurement and fails a shipping drop costs far more than the saving it generated.
Neck finishes and dimensional control
Pill bottles use continuous thread finishes, often with a tamper band below the thread and a flat sealing land under the cap. Neck diameters up to about 38 millimeters are common for small containers, and wider finishes are used for supplements. The controlled dimensions are inner diameter, outer diameter, ovality, thread profile and pitch, band thickness and the height of the sealing land. These are measured on the mold and on production bottles, because a neck error is almost always a core rod or cavity issue rather than a blowing issue.
6. Resin Choice, Barrier Needs and Material Cost
Which resins are used
Polypropylene is the most common choice for a pill bottle because it is stiff, inexpensive and resistant to the moisture that degrades many solid dose products. High density polyethylene is used where impact resistance and a softer sealing surface matter. Polystyrene and PET appear where clarity is important, and multilayer structures are used when oxygen or moisture barrier dominates the formulation. The resin decision affects the bottle cost, the mold shrinkage and the neck tolerance at the same time, so it has to be settled before the tooling is ordered.
Material cost per bottle
Medical grade polypropylene sits around 1,250 to 1,900 US dollars per metric ton, while high density polyethylene is generally lower and PET or specialty barrier resins are higher. Color masterbatch at one to three percent adds a modest amount, and a slip or antistatic additive may be needed for high speed filling. A 15 gram polypropylene bottle therefore carries roughly 0.019 to 0.029 US dollars of resin. That number looks small until it is multiplied by tens of millions of bottles, which is why a fraction of a gram of wall thickness and a consistent regrind policy are worth real money.
7. Complete Machine and Tooling Price List
What a quotation should include
A complete cell includes the injection blow machine, the rotary index mechanism, the core rods and neck inserts, the blow cavities, the hot runner, the hydraulic or servo drive, the compressed air and cooling connections, the takeout conveyor, the control system and the first spare kit. Resin drying and conveying, chilled water, and any vision inspection are usually separate. The price moves mainly with shot capacity, clamping force, cavitation and the precision of the neck tooling, not with the number of bottle sizes the sales brochure mentions.
Equipment price list
The figures below are delivered prices in US dollars for a mid size three station injection blow machine producing 20 to 300 milliliter bottles. Installation, foundations, training and tooling for additional bottle sizes are separate. The wide bands on molds and core rods reflect cavitation and the complexity of the neck, since a tamper band with fine bridges is a more demanding tool than a plain threaded finish.
| Item | Typical price in US dollars |
|---|---|
| Injection blow machine, 40 to 50 millimeter screw | 180,000 to 520,000 |
| Servo rotary indexing upgrade | 35,000 to 110,000 |
| Hot runner system | 25,000 to 90,000 |
| Core rod and neck insert set per cavity | 8,000 to 25,000 |
| Blow cavity set per cavity | 6,000 to 18,000 |
| Tamper band precision tooling package | 12,000 to 40,000 |
| Hopper dryer and conveying package | 8,000 to 28,000 |
| Chilled water and air preparation | 15,000 to 45,000 |
| Takeout conveyor and neck up orienting | 10,000 to 35,000 |
| Vision inspection for neck and band | 30,000 to 95,000 |
| Control and batch data recording | 18,000 to 60,000 |
| First spare and wear parts kit | 10,000 to 30,000 |
Reading the total realistically
Adding the midpoint of each item gives roughly 0.48 million US dollars for a configured cell with two cavities and basic inspection, and a pharmaceutical installation adds 40,000 to 90,000 US dollars for commissioning, qualification support and training. Tooling for a second bottle size is a separate cost and can add 60,000 to 180,000 US dollars. A buyer should resist choosing the smallest machine that can physically fit the bottle, because a machine running near its shot and clamp limits will struggle to hold the neck tolerance that the capping line requires.
8. Injection Station, Screw and Hot Runner
Screw and shot capacity
The injection station plasticizes the resin and delivers a controlled shot to the neck and preform cavities. Wanplas injection blow machines use screws of 40, 45 and 50 millimeters with injection volumes from 176 to 400 grams, which is ample for small pill bottles even with several cavities. The machine should be chosen so the shot is a comfortable share of the screw capacity, because a very small shot from a large screw gives poor residence control and inconsistent melt temperature. Barrel heating power ranges from 7.2 to 12 kilowatts across the range, with three to five control zones, and even heating matters more than peak power when a temperature sensitive medical resin is used.
Hot runner and gate layout
A hot runner delivers the melt to each cavity at the same temperature and pressure, which is how a multi cavity machine keeps bottle weights and neck dimensions consistent. The gate position is chosen so it does not cross the sealing land or the tamper band, since a gate mark on either surface can interfere with the closure or create a stress point. Needle valve gates give a cleaner mark and remove cold sprue waste, at a cost of roughly 25,000 to 90,000 US dollars. For a medical bottle that saving is often justified by fewer cosmetic rejects rather than by the resin alone.
Injection pressure and holding
The neck is filled and packed under injection pressure before the body is stretched, so the holding phase is where thread definition and band strength are set. Too little holding leaves a sink at the thread root and a weak band; too much packs stress into the neck and causes it to ovalize as it cools. The clamp force at the injection station, from 350 to 750 kilonewtons across the machine range, has to be high enough to keep the neck mold closed against that pressure. A machine selected with too little clamp will flash the band even when the temperature and speed are correct.
9. Core Rod, Neck Mold and Preform Design
The core rod is the real mold
In injection blow molding the core rod carries the inside of the neck and the starting wall of the preform, then travels with the bottle through the blow and strip stations. Its temperature is controlled independently, because a rod that is too cold freezes the preform and prevents the body from stretching, while a rod that is too hot makes the neck sag. The rod also has to survive repeated heating and cooling without losing dimensional accuracy. Wanplas treats the rod, the neck insert and the blow cavity as a matched set, because a tolerance error shared between them is the most common cause of systematic neck drift.
Preform wall distribution
The preform is not a simple tube; its wall is thicker at the shoulder and the neck transition and thinner where the body will stretch most. That distribution decides how the material thins during blowing and whether the finished bottle has even walls. An uneven preform produces a bottle with a thin panel that fails top load and a thick patch that wastes resin. The design is developed with a blow up ratio study and confirmed by sectioning molded bottles, not by copying a preform from a different bottle size.
Neck inserts and shrinkage compensation
The neck mold is cut slightly oversize to allow for the shrinkage of the resin as it cools. Because different polymers shrink by different amounts, changing resin grade can move every neck dimension even though the tool has not changed. That is why a resin change on a pharmaceutical bottle always requires a new dimensional check and a capping trial. Inserts should be made replaceable so a plant can correct a systematic error without buying a complete mold, and Wanplas recommends keeping one spare insert set for the highest volume bottle.
10. Blow Station and Stripping
Blowing and cavity cooling
At the blow station compressed air enters through the core rod and expands the warm preform against the cooled cavity. Blow pressure is modest compared with injection pressure, but the timing and the air path matter: air that enters too fast can cool the preform surface before it stretches, and an uneven path can push the wall toward one side. Compressed air pressure on the Wanplas range is 0.8 to 1.0 megapascal with a displacement of at least 0.7 to 0.8 cubic meters per minute. The cavity water channels are arranged to cool the shoulder and the base first, since those areas retain the most heat and control when the bottle can be stripped.
Stripping without damaging the neck
The stripper plate pushes the bottle off the rod while the neck and tamper band are still warm enough to deform. Plate alignment and stripping speed therefore determine whether the band stays round or stretches on one side. A misaligned plate can also mark the sealing land, which shows up later as a leak on the filling line. The machine’s blow molding clamp, from 40 to 150 kilonewtons across the range, holds the cavity closed during blowing and is sized to the projected area of the bottle. A buyer running wide bottles should check this figure rather than looking only at injection clamp.
11. Neck Accuracy and the Cost of Capping Failure
The controlled dimensions
A bottle neck is out of tolerance when any of its controlled dimensions leaves the drawing limit: inner and outer diameter, ovality, thread profile and pitch, band thickness and the height of the sealing land. In injection blow molding most of these are set by the core rod and neck insert, not by the blowing step. Inner diameter error usually points to the rod or the insert, outer diameter error to the neck cavity, and systematic drift in both to resin shrinkage. Diagnosing which one has moved is the first step, because the corrective action is completely different in each case.
Why failures appear at the capper
A neck defect is expensive because it is often discovered far from where it was made. A bottle that looks acceptable on the molding line can fail when a cap is applied at high speed, and by then it may be part of a large lot. An undersized inner diameter makes the cap cross thread, an oversized one leaks, an oval neck causes intermittent torque, and a weak tamper band breaks during capping rather than during opening. Wanplas recommends checking neck gauges at the machine and running a capping trial at every mold, resin or closure change.
12. Cleanliness, Contamination and Changeover
Keeping the mold environment clean
A pharmaceutical bottle does not need a full cleanroom at the molding stage, but it does need a controlled environment that keeps dust, oil mist and loose fibers away from the open bottle. Enclosed material handling, filtered compressed air and oil free air preparation are worthwhile because contamination entering at the blow station stays in the finished container. Machine surfaces should be cleanable, and the external oil tank arrangement on Wanplas machines makes maintenance and cleaning easier than a machine with oil reservoirs inside the guarded area.
Color and resin changeover
A change from one resin or color to another requires purging the barrel and hot runner, conditioning the core rods to the new temperature and then bringing the neck dimensions back into tolerance. The purge material is waste, and the first production bottles after a change may be off specification until temperatures settle. A documented purging sequence and a hot runner designed for fast color change can cut purge mass substantially, at an added cost on the tooling. Plants running many short campaigns should value that feature more than a small gain in cycle time.
Batch records and traceability
Pharmaceutical buyers expect to connect a bottle lot to the resin batch, the mold, the machine settings and the inspection results. The controller can record melt and mold temperatures, injection pressure, cycle time and cavity identity for each run. The practical benefit is that a complaint about a broken band or a leaking cap can be traced to a shift or a material lot instead of requiring a broad recall. Wanplas recommends agreeing the record format with the customer before commissioning, because adding traceability after a line is installed means reworking both the control package and the operating procedure.
13. Quality Control and Performance Testing
Routine checks on the line
Operators check bottle weight, neck dimensions, band appearance, wall thickness at defined points and top load on a sample. Weight is a fast proxy for wall thickness and shot consistency, so it is tracked by cavity, because a single cavity running heavy or light points to a gate or rod problem. The tamper band is inspected for complete bridges and a clean break line, and the sealing land is checked for gate marks or flash. These checks are quick enough to run several times per shift and they catch the defects that will otherwise appear at the capper.
Performance tests for the finished bottle
Bottles are tested for top load, drop resistance, closure torque and leak behavior, and for the force needed to break the tamper band. Moisture transmission matters for a solid dose product, and the bottle plus closure is tested as a system rather than as separate parts. A band that breaks too easily can fail in shipping, while one that is too strong frustrates the patient or fails at capping. The aim is a narrow, repeatable band break force, which is another reason the band tooling and the resin shrinkage have to be managed together.
Test cost in context
A basic in house lab with a caliper, a force gauge, a top load tester and a leak rig represents roughly 15,000 to 40,000 US dollars and pays for itself when it prevents one rejected lot. More specialized barrier and migration testing is usually outsourced and needed only at material or design changes. The real cost of testing is the time a line waits for a result, so Wanplas recommends defining which checks release a campaign and which run in parallel. A fast band break check at the machine is worth more than a detailed report that arrives after the pallet has shipped.
14. Process Parameters and the Cost of Deviation
The variables that control the bottle
Melt temperature and injection pressure control how the neck fills and how much material goes into each preform. Core rod temperature controls how much the body can stretch, and blow pressure and timing control how the wall distributes against the cavity. Cooling time decides whether the bottle can be stripped without deforming. Clamp force at both stations keeps the neck mold and blow cavity closed against pressure. A deviation in any of these shows up either as a neck error at the capper or as a thin wall that fails a drop test, which is why they are controlled together in the recipe.
Parameter table
The table gives representative operating windows for a three station injection blow machine making small pharmaceutical bottles. These are starting points for trials, not settings for a specific resin or neck design, and the buyer should refine them during acceptance with the actual tool and closure.
| Parameter | Typical window | Cost of deviation |
|---|---|---|
| Screw diameter | 40, 45 or 50 mm | Wrong shot size, poor melt control |
| Injection volume | 176 to 400 g | Shot near limit reduces stability |
| Injection clamp | 350 to 750 kN | Flash on the tamper band |
| Blow clamp | 40 to 150 kN | Parting line and ovality |
| Barrel heating power | 7.2 to 12 kW | Uneven melt and thread shots |
| System pressure | 14 MPa | Unstable injection and holding |
| Compressed air pressure | 0.8 to 1.0 MPa | Thin wall or incomplete body |
| Air displacement | At least 0.7 to 0.8 cubic meters per minute | Slow blowing and longer cycle |
| Cooling water | 3 cubic meters per hour | Warped neck on stripping |
| Total power | 25 to 52 kW | Utility sizing and energy cost |
| Product volume | 2 to 1,000 ml | Outside range needs another machine |
From settings to money
A neck that drifts by a fraction of a millimeter may still look acceptable but will fail at a high speed capper, and by then the whole lot is at risk. A band that breaks too lightly can turn a shipping test into a customer complaint. These losses rarely appear as a machine stoppage, so they are easy to overlook. Wanplas recommends converting each defect into an amount per thousand bottles during commissioning, so the operator can see that holding a stable core rod temperature is worth more than squeezing an extra cycle out of the machine.
15. Output, Energy, Unit Cost and Payback
What determines real output
Injection blow output is set by the slowest station, which is usually cooling in the blow mold, multiplied by the number of cavities. A small pill bottle on a two cavity machine can produce several thousand bottles per hour, while a larger bottle or a thicker wall lengthens the cycle and reduces that figure. Catalog cycle times assume a stable melt and a clean strip, so they should be treated as an upper bound. The buyer should size the machine from the annual bottle volume with 15 to 25 percent spare capacity rather than buying a single line that must run continuously to meet demand, because a pharmaceutical program rarely has a perfectly flat schedule.
Energy and utilities
Total connected power on the Wanplas range is 25 to 52 kilowatts, covering barrel heating, mold heating, the drive motor and auxiliary systems. Compressed air at 0.8 to 1.0 megapascal and cooling water around 3 cubic meters per hour add utility costs that are easy to underestimate in the project budget. Because the machine runs three stations at once, the energy per bottle is low once it is producing steadily, but frequent starts and long changeovers erode that advantage. A plant with unstable chilled water will lose more output to longer cooling cycles than it would save by choosing a smaller compressor.
Bottle cost and payback
A 15 gram polypropylene bottle carries roughly 0.019 to 0.029 US dollars of resin, and molding conversion adds about 0.010 to 0.025 US dollars once energy, labor, tooling amortization and rejects are included. Inspection and clean handling add a little more, putting the finished empty bottle near 0.035 to 0.060 US dollars before margin. A configured cell around 0.48 million US dollars producing 30 to 60 million bottles a year can pay back in roughly two to four years, depending on the value placed on avoiding capping line rejects. A packer currently buying bottles from an outside converter will often see a faster return, because the current supplier margin is eliminated.
16. Wanplas Equipment Recommendation and Buying Checklist
Which Wanplas equipment fits this application
Wanplas supplies the three station injection blow platform that matches this task, with screws of 40, 45 and 50 millimeters, injection volumes from 176 to 400 grams, injection clamp from 350 to 750 kilonewtons and blow clamp from 40 to 150 kilonewtons. Product volume runs from 2 to 1,000 milliliters, with maximum bottle height around 200 to 230 millimeters and diameter up to 100 millimeters. The company lists medical packing bottles as a main application, and the servo driven rotary structure uses a single cylinder injection mechanism for even force and lower energy use. For a tamper evident pill bottle, Wanplas recommends the model with adequate clamp reserve and a precision neck tooling package, because the break band and thread are the features that decide whether the package works.
What to settle before signing
Fix the bottle drawing, the neck finish, the tamper band geometry, the closure design, the resin and the annual volume before the order is placed. Then confirm cavity count, core rod and neck insert scope, hot runner layout, vision inspection, drying and conveying, and the batch record format. The bottle and closure must be developed as a pair, so the closure supplier should see the neck drawing before the mold is cut. Wanplas recommends running a capping trial with production closures during acceptance rather than judging the neck only with a gauge, because that is where the real failure appears.
Acceptance test and spare parts
Require a four hour run with the production resin and closure, then check neck dimensions by cavity, band break force, bottle weight, wall thickness, top load and leak behavior. Include a color or resin change to verify purge loss and dimensional recovery, and confirm that the batch record exports correctly. Hold 10 percent of the machine price until the first commercial lot passes at the filling line. Include a spare core rod set, spare neck inserts, a stripper plate, a set of heating bands and seals, because any one of these can stop a three station machine for days when it wears out.
Frequently Asked Questions
How much does a medical pill bottle injection blow molding machine cost?
A three station machine with two cavities, core rods, hot runner and basic inspection typically costs 350,000 to 620,000 US dollars. A higher cavitation cell with vision inspection, precision tamper band tooling and batch recording can reach 900,000 US dollars, with installation and training adding 40,000 to 90,000.
Why not use extrusion blow molding for pill bottles?
Extrusion blow molding pinches the parison and blows the neck, which leaves a weld and flash and gives poorer neck accuracy. A pill bottle depends on the neck for sealing and tamper evidence, so injection blow molding is preferred because the neck is injected around a core rod before the body is blown.
What bottle volumes can this machine produce?
The Wanplas injection blow platform covers 2 to 1,000 milliliters, with maximum bottle height around 200 to 230 millimeters and diameter up to 100 millimeters depending on machine size. That range covers most solid dose, sample and supplement containers.
How does a tamper evident neck work?
A thin break band sits below the thread and is joined to the bottle by small bridges. Twisting the cap the first time leaves the band on the neck and snaps the bridges, creating a visible gap. The band has to break cleanly every time, so its tooling and the resin shrinkage are controlled together.
What resin is normally used for a pill bottle?
Polypropylene is the most common choice because it is stiff, inexpensive and moisture resistant, typically 1,250 to 1,900 US dollars per metric ton in medical grade. High density polyethylene is used where impact resistance matters, and PET or multilayer structures are chosen when clarity or barrier performance dominates.
Which neck dimensions matter most?
Inner and outer diameter, ovality, thread profile and pitch, tamper band thickness and the height of the sealing land are all controlled. Most errors come from the core rod, neck insert or resin shrinkage rather than from the blowing step, so the corrective action depends on which dimension has moved.
Can regrind be used in pharmaceutical bottles?
Only under a documented and limited policy. A small amount of clean regrind from the same resin family can often return to the body, but the material has a heat history and is usually kept out of critical neck areas. Wanplas recommends separate collection and clear labeling of regrind from each resin.
What should an acceptance test cover?
Run four hours with production resin and closures, then check neck dimensions by cavity, band break force, bottle weight, wall thickness, top load and leak behavior. Include a color or resin change and verify the batch record export. Hold part of the price until the first lot passes at the filling line.
Conclusion
A medical pill bottle injection blow molding machine wins on the neck. Because the neck is injected around a core rod before the body is blown, the thread, sealing land and tamper band are formed under pressure and held to a tolerance that an extrusion blow process cannot match. The same three station cycle also delivers a clean, trim free bottle with no pinch weld, which suits a pharmaceutical filling line.
The economics are dominated by consistency rather than by resin price alone. A 15 gram polypropylene bottle carries only 0.019 to 0.029 US dollars of material, but a neck defect discovered at the capper can condemn a large lot. A configured cell near 0.48 million US dollars pays back in two to four years when it removes that risk, and faster when it replaces an outside bottle supplier.
Wanplas recommends a three station machine with a 45 or 50 millimeter screw, clamp reserve above the minimum, a precision neck tooling package and vision inspection for small medical bottles. Defined around the bottle and closure as one system, the line produces a tamper evident container that seals, breaks and presents reliably through filling, shipping and use.

