A garden hose looks simple, but a fiber reinforced one is a three part composite made in one continuous pass. A soft PVC inner tube is extruded, cooled, wrapped in a knitted or braided fiber sleeve, then covered with a second PVC layer. The fiber carries the pressure load, the PVC carries the water and protects the yarn, and the line must bond all three without crushing the reinforcement. This guide describes the whole production decision, from compound and yarn cost through extruders, braider, cooling, quality testing and the full investment model. Every major item carries a planning price in US dollars.
1. What a PVC Fiber Reinforced Garden Hose Line Produces
A PVC braided hose line makes flexible hose from 8 millimeters to 50 millimeters in diameter. The wall is PVC and the fiber sits in the middle of that wall. Depending on the order, the line produces single braid, three layer braid or five layer braid hose in different colors. The line is built from two single screw extruders, dies, cooling water tanks, haul off units, a braiding machine and winders. The inner layer is extruded first, cooled, braided, then covered by the second extruder, cooled again, pulled and wound.
Why the fiber makes the difference
Plain soft PVC tube stretches under pressure and kinks easily. A fiber sleeve takes the hoop load so the hose can hold higher pressure with a thinner wall and less resin. The braided hose resists extrusion, corrosion and static electricity, withstands high pressure and runs smoothly. That combination suits garden and lawn irrigation, high pressure water, combustible gas and liquid transfer, and heavy suction or delivery of liquid sludge.
Who buys the line
A horticultural supplier wants 12 to 19 millimeter hose for retail reels and irrigation kits. An industrial distributor wants 25 to 50 millimeter hose for water transfer and slurry work. A converter with an existing PVC extrusion business adds a braid line to move from rigid pipe into higher margin flexible products. Each buyer needs a different screw size, braider capacity and winder, which is why the line is sold in diameter bands rather than as one universal machine.
2. Hose Construction: Inner Tube, Fiber Layer and Outer Cover
Internal diameter, wall and fitting fit
Hose is sold by internal diameter, so the inner tube die sets the dimensions that matter to the customer. A 12 millimeter hose must accept a 12 millimeter barb without splitting, yet hold a tight enough grip that the coupling does not weep at working pressure. A wall that is 0.15 millimeters too thin at one point can split when a fitting is pushed home. A wall that is too thick makes the barb hard to insert and raises resin cost on every meter. The practical tolerance on internal diameter is plus or minus 0.15 millimeters, with wall thickness held within plus or minus 0.10 millimeters around the circumference.
Fitting compatibility should be checked with the actual coupling before the die is released. A sample of two meters is cut, a barb is inserted and the assembly is pressure tested. The same check should be repeated after the hose has been stored for a week, because plasticizer migration slowly changes hardness and grip. A supplier who only quotes a die diameter without asking about fittings has not finished the specification.
Three layer and five layer structures
The standard construction is inner PVC, one fiber braid and outer PVC. A three layer hose adds a second PVC tie layer or a second braid for higher pressure. A five layer build alternates PVC and fiber to reach the top pressure classes. Each extra layer means another extruder or another pass through the braider and adds both material and capital cost. A project should choose the lowest layer count that meets the pressure rating, because a five layer line costs far more to buy and to change over.
Braid versus knit
A braid crosses two yarn paths over and under each other to form a diamond pattern that resists both expansion and twist. A knitted or crochet type layer uses loops and is cheaper and faster to make but gives less burst strength. The line described here can produce either with the right head and yarn. Braided hose is the default for pressure service; knitted reinforcement suits light duty garden hose where flexibility and cost matter more than burst rating.
Wall thickness and bond
The inner tube must be thick enough to survive the braiding tension without collapsing, typically 0.8 to 2.0 millimeters depending on diameter. The outer cover must flow around the yarn and fuse with the inner tube through the braid openings. If the inner tube is too cold when it reaches the braider, the two PVC layers will not weld and the hose delaminates under pressure. If it is too hot, the braid sinks into the wall and the outside becomes lumpy. The cooling distance between the first die and the braider is therefore a process variable, not just a machine layout detail.
3. PVC Compound and Plasticizer Cost
Garden hose uses suspension PVC with a K value around 65 to 70, plasticized to a Shore A hardness near 70 to 85. The inner tube needs enough plasticizer for flexibility and low temperature bend; the outer cover needs harder compound for abrasion and weather resistance. Many plants run two recipes on the two extruders so the inner layer stays soft while the cover resists scuffing.
General purpose PVC resin costs roughly 1,100 to 1,600 US dollars per metric ton. A common phthalate plasticizer adds 1,300 to 1,900 US dollars per ton, while lower migration types cost 2,200 to 4,800 US dollars per ton. Heat stabilizer, lubricant, filler and pigment bring a finished hose compound to about 1,800 to 2,900 US dollars per ton for a standard garden grade. A 12 millimeter hose with a 2 millimeter wall uses about 75 grams of compound per meter, putting resin cost near 0.14 to 0.22 US dollars per meter before fiber and conversion.
Plasticizer choice and migration
Cheap phthalate plasticizer gives good flexibility at low cost but can migrate into soil or oily fluids over time. For premium irrigation hose, a lower migration plasticizer adds 0.03 to 0.09 US dollars per meter of compound cost yet supports a higher retail price and a cleaner handling claim. Stabilizer choice matters too: a lead based system is cheap but restricted in many markets, while calcium zinc systems cost more and need tighter temperature control. The formulation should be fixed before the screw is specified, because plasticizer level changes melt viscosity and output.
4. Reinforcement Yarn: Polyester, Nylon and Yarn Cost
Polyester yarn is the standard reinforcement because it combines tensile strength, low water absorption and a moderate price. Nylon is stronger and more elastic but absorbs water and costs more, which suits heavy suction hose rather than garden irrigation. Yarn is supplied as continuous filament on cones and fed to the braider spindles, where each end is tensioned before it enters the carrier.
Polyester industrial yarn in the 500 to 1,500 denier range costs roughly 2.2 to 4.5 US dollars per kilogram. A 12 millimeter hose may carry 18 to 32 ends depending on braid density, adding about 0.02 to 0.06 US dollars per meter. On a 25 millimeter hose the yarn cost can reach 0.10 US dollars per meter. Yarn is often a smaller line item than PVC, but an uneven tension across spindles causes weak spots that no amount of compound quality can fix.
Yarn tension and braid coverage
Every carrier must deliver the same tension. A loose end floats on the tube and leaves a gap in coverage; a tight end cuts into the soft PVC and reduces wall thickness at that point. Tension devices on each spindle should be checked at every changeover, and a broken end must stop the line rather than run as a defect. Braid coverage is usually specified as the percentage of the tube surface covered by yarn, with 85 to 95 percent typical for pressure hose. Higher coverage improves burst strength but adds yarn cost and slows the braider.
5. Line Architecture and Equipment Price List
The line is a sequence of stations: resin handling, two extruders, inner die, first cooling bath, haul off, braiding machine, outer crosshead die, second cooling bath, final haul off, printer if required and winder. The two extruders and the braider set the pace; the baths and winders must be long enough and fast enough to keep up. The table gives planning prices in US dollars for a complete 12 to 32 millimeter line.
| Item | Scope | Price in US dollars |
|---|---|---|
| Material handling | Hopper dryer, loader, feeder for two extruders | 18,000 to 48,000 |
| Primary extruder | 45 or 65 mm single screw, drive and barrel heating | 65,000 to 180,000 |
| Secondary extruder | 45 or 65 mm single screw for outer cover | 60,000 to 165,000 |
| Inner die and outer crosshead | Die set for one diameter band | 24,000 to 78,000 |
| First cooling bath | Stainless tank, water circulation and guides | 14,000 to 38,000 |
| Braiding machine | Carriers, yarn creel, tension control and drive | 75,000 to 240,000 |
| Second cooling bath | Longer tank for the finished wall | 18,000 to 52,000 |
| Haul off units | Two claw traction with variable frequency drive | 16,000 to 44,000 |
| Printer and winder | Surface printer, length counter, reel winding | 22,000 to 68,000 |
| Controls and instrumentation | Temperature, line speed, diameter gauging and alarms | 28,000 to 85,000 |
| Installation and commissioning | Layout, wiring, water connections, training and trial run | 20,000 to 55,000 |
A complete 8 to 12 millimeter line normally lands between 320,000 and 620,000 US dollars. A 16 to 32 millimeter line with a larger braider costs 480,000 to 900,000 US dollars, and a 32 to 50 millimeter heavy duty line reaches 650,000 to 1,200,000 US dollars. Die sets for extra diameters add 8,000 to 26,000 US dollars each, and a second braider for five layer hose adds 70,000 to 230,000 US dollars.
6. Extruders, Screws and Melt Preparation
Barrel temperature profile
A plasticized PVC profile typically climbs from roughly 140 degrees Celsius at the feed zone to 175 or 185 degrees Celsius at the die. The exact curve depends on the K value of the resin and the plasticizer package. A rising profile protects the feed throat from premature melting, which otherwise causes bridging and erratic output. Some compounds benefit from a slight reduction in the metering zone to limit shear heating. Barrel zones are controlled independently, and the melt thermocouple at the die is the number to trust rather than the barrel setpoint.
A useful start up routine brings the die and the last barrel zone to temperature first, then heats the feed zones while the screw turns slowly. A cold start against a closed die can overpressure the machine and damage the screw. Once the melt is uniform, output is increased in steps and the braider ratio is set only after the inner tube diameter has stabilized. Rushing this sequence is the most common reason a new line produces weeks of off specification hose.
The official line uses single screw extruders with strong plasticizing performance. The three diameter bands are built around a 45 millimeter screw for 8 to 12 millimeter hose with 35 kilowatts total power, a 65 millimeter screw for 16 to 32 millimeter hose with 50 kilowatts, and a 65 millimeter screw for 32 to 50 millimeter hose with 60 kilowatts. These figures describe the whole line, not just the drive motor.
Screw design for plasticized PVC
A plasticized PVC screw uses a compression ratio near 2.2 to 2.8 and a length to diameter ratio of 25 to 30. The goal is gentle, uniform melting without generating enough shear heat to degrade the stabilizer. A barrier section and a short mixing zone help distribute plasticizer, but an aggressive mixer can raise melt temperature and cause yellowing. Spare screws cost 9,000 to 24,000 US dollars and are worth ordering with the machine, because a damaged screw stops the whole line for weeks.
Feeding and melt filtration
PVC compound is fed by a loss in weight feeder or a simple volumetric hopper depending on the accuracy needed. A hopper dryer removes surface moisture, and a screen pack or continuous filter catches contamination before the die. A 40 to 80 micron filter costs 60 to 220 US dollars per element and 3,000 to 14,000 US dollars a year at typical output. A screen change that is too infrequent raises melt pressure and can push the inner tube diameter out of tolerance.
7. Crosshead Die and Layer Bonding
The first die forms the inner tube. The second is a crosshead die through which the braided tube passes while the outer PVC flows around it. The crosshead must center the braided tube precisely; an off center core gives a thin wall on one side and a thick wall on the other, and the thin side fails the burst test first. A die set for one diameter band costs 24,000 to 78,000 US dollars, with 4 to 8 centering screws and adjustable die lips.
Bonding window
The outer melt must be hot enough to soften the surface of the cooled inner tube and flow between the yarn strands. If the inner tube is too cold, the layers separate; if too warm, the braid deforms. Operators tune the distance from the first bath to the crosshead and the temperature of the outer melt together. A pull through test on a sample in 1,000 to 3,000 US dollars of test equipment confirms that the two layers actually weld.
8. Braiding Machine, Carriers and Braid Angle
The braider is the heart of the reinforced line. Yarn cones sit on a creel, each end passes through a tension device, and carriers move in two opposing paths around the tube. The crossing point lays the diamond pattern onto the cooled inner tube. Carrier count depends on hose diameter and desired coverage; a small hose may use 16 to 24 carriers, while a 50 millimeter hose uses 48 or more. A larger braider with more carriers costs 75,000 to 240,000 US dollars.
Braid angle and pressure
The angle of the yarn to the hose axis decides how the hose behaves under pressure. An angle near 54 degrees balances hoop strength and axial stability. A steeper angle resists expansion strongly but lets the hose lengthen; a shallower angle holds length but bulges. Changing the angle means changing the ratio of braider speed to haul off speed, so the drive must be synchronized. A variable frequency drive on the haul off and a encoder feedback loop keep the ratio stable when line speed changes.
Yarn breaks and splices
A broken yarn leaves an unbonded patch that becomes a burst point. Modern machines stop on a break and mark the location. If a splice is unavoidable, it should be taped flat and recorded so the section can be cut out at the winder. A line that keeps running after a break can produce hundreds of meters of downgrade hose before anyone notices. A yarn break detector adds 4,000 to 14,000 US dollars and usually pays for itself in one avoided quality incident.
9. Cooling, Haul Off and Winding
Two cooling baths are used. The first sets the inner tube before braiding, and the second cools the completed wall before winding. Water temperature is typically 15 to 25 degrees Celsius, and bath length depends on line speed; 4 to 8 meters is common on a medium line. Warm water leaves the hose soft and prone to flattening on the reel, while very cold water can lock in stress and cause later kinking.
Haul off traction
The official line uses a two claw haul off with speed governed by a variable frequency drive. The claws must grip without marking the soft cover. Rubber faced tracks and adjustable pressure handle most garden hose; a foam cover or a wider track is needed for thin wall product. The haul off sets line speed and therefore the braid angle, so its speed control must be smooth and repeatable rather than merely adjustable.
Winding and packing
Hose is wound onto reels of 25, 50 or 100 meters, or coiled for retail bags. A length counter triggers the cut, and the winder must maintain constant tension so the coil does not dig into itself. An automatic reel changer costs more but removes an operator and reduces the chance of a tail defect. Printing a batch code on the cover at the winder links any later complaint to the yarn lot and compound batch.
10. Process Window and Control
The table below gives starting values for a 12 to 19 millimeter braided garden hose. Every value shifts with compound hardness, yarn type and line speed, so these are commissioning targets rather than fixed rules.
| Parameter | Target | Deviation effect |
|---|---|---|
| Barrel zones | 140 to 185 degrees Celsius | Overheat yellows and degrades stabilizer |
| Inner melt temperature | 165 to 185 degrees Celsius | Too cool gives poor tube surface |
| Outer melt temperature | 170 to 195 degrees Celsius | Too cool causes delamination |
| Melt pressure | 8 to 22 MPa | Rise means blocked screen or cold melt |
| Line speed | 10 to 45 meters per minute | Faster than cooling gives deformation |
| Braid angle | 48 to 56 degrees | Wrong angle changes burst and length |
| Braid coverage | 85 to 95 percent | Low coverage lowers burst pressure |
| Yarn tension per end | 0.8 to 2.5 newtons | Uneven tension creates weak spots |
| First bath water | 18 to 25 degrees Celsius | Warm tube sinks braid into wall |
| Second bath water | 15 to 25 degrees Celsius | Warm hose flattens on the reel |
| Wall thickness tolerance | Plus or minus 0.10 millimeter | Thin side fails the burst test |
| Outer diameter tolerance | Plus or minus 0.15 millimeter | Affects coupling fit and reel length |
| Haul off traction force | 30 to 180 newtons | Too high flattens, too low slips |
A diameter gauge with closed loop control of the haul off costs 28,000 to 85,000 US dollars and holds wall thickness far better than manual adjustment. Data logging of temperatures, pressures, line speed and braider ratio adds 8,000 to 24,000 US dollars and makes a customer complaint traceable to a shift and a yarn lot.
11. Pressure Rating, Testing and Quality Control
Weathering and low temperature behavior
Garden hose spends its life outdoors, so ultraviolet exposure and winter temperatures matter as much as burst pressure. A stabilizer package that survives extrusion but lacks a light stabilizer will chalk and crack after one season. A low temperature bend test at minus 10 degrees Celsius shows whether the compound stays flexible enough to unroll in early spring. Both tests can be run with a small chamber and a UV cabinet costing 15,000 to 45,000 US dollars, a worthwhile investment for a brand that carries a multi year warranty.
Plasticizer loss also changes the hose over time. A coupon aged in warm air and weighed before and after gives a quick measure of migration. If the outer cover is noticeably harder after aging, the compound should be reformulated before the product reaches the trade. A soft inner layer with a harder, better stabilized cover is usually the most economical way to meet both flexibility and weather requirements.
Hose is sold by inside diameter, wall thickness and working pressure. A typical 12 millimeter garden hose has a working pressure near 8 to 12 bar and a burst pressure two to three times higher. A heavy duty 25 millimeter braided hose may carry 15 to 25 bar working pressure. Pressure capability depends on yarn strength, braid angle, coverage and the quality of the bond between layers, not simply on wall thickness.
Routine tests
A hydrostatic test holds a sample at 1.5 times working pressure for a defined period and checks for leakage or visible deformation. A burst test runs samples to failure and records the pressure, with a smaller sample set taken each shift. Diameter and wall thickness are measured at several points around the circumference because eccentricity is common on a crosshead. A kink test, a low temperature bend and a coupon peel test complete the routine set. A small in house lab with a pressure rig and gauge costs 12,000 to 45,000 US dollars.
Common defects and causes
Delamination usually means the inner tube was too cold at the crosshead. A wavy outside diameter often comes from uneven haul off traction or a braid that is too loose. A low burst result points to broken yarn, wrong braid angle or insufficient coverage. Yellowing indicates overheated compound or a stabilizer that cannot handle the barrel profile. Each defect has a machine setting and a material cause, so the log must record both.
12. Color, Striping, Printing and Branding
Color is added at the compound stage or through a color feeder on the outer extruder. A color change on a two extruder line takes 20 to 60 minutes and wastes 30 to 90 kilograms of compound, so production should be scheduled by color family. A stripe can be extruded through a second small channel in the crosshead, adding 8,000 to 24,000 US dollars. Surface printing puts a brand name, diameter, pressure rating and batch code on the cover; a simple printer costs 9,000 to 28,000 US dollars and an inline vision check adds 6,000 to 18,000 US dollars.
13. Output, Changeover and Scrap
Line balance and cavitation
The slowest station sets the real output. On a small hose the braider is usually the limit, because carrier speed and yarn tension cannot be pushed beyond a safe range. On a large hose the extruder output and cooling bath length become the limit. A line bought with a fast extruder and a small braider will cavitate at the braider and run far below its advertised speed. Ask the supplier to identify the bottleneck for each diameter and to demonstrate a stable run at that station with the real yarn.
Accumulation between stations is deliberately small on this line, so a stop at the winder backs up quickly. A short accumulator or a buffer table adds 6,000 to 18,000 US dollars but gives the operator time to change a reel without slowing the braider. On a high volume line that buffer often pays back in a single shift of avoided downtime.
Output depends on diameter, wall thickness and line speed. A 12 millimeter line commonly runs 15 to 35 meters per minute, while a 32 to 50 millimeter line runs 8 to 20 meters per minute. At 25 meters per minute a 12 millimeter line produces about 1,500 meters per hour, or 12,000 meters in an eight hour shift before losses. Changeover between diameters needs a new die set, a braider ratio change, new yarn cones and a cooling adjustment, typically 60 to 150 minutes.
Scrap and rework
Startup scrap, screen changes, color changes and yarn breaks typically add 3 to 8 percent to material use. Clean PVC trim can be reground and fed back at 10 to 20 percent on the inner layer, but the outer cover should stay virgin for weather resistance. A granulator costs 8,000 to 28,000 US dollars and usually pays back within a year on a medium line. Yarn waste cannot be recycled and should be counted as a direct cost per meter.
14. Utilities, Floor Space and Staffing
Total installed power follows the official bands: 35 kilowatts for the 8 to 12 millimeter line, 50 kilowatts for 16 to 32 millimeter and 60 kilowatts for 32 to 50 millimeter. A chiller, water circulation pumps and the braider drive add to the plant total. Cooling water demand is roughly 3 to 8 cubic meters per hour depending on line speed and bath length. Floor space for a complete line is 18 to 35 meters by 4 to 6 meters, plus room for yarn storage and finished reels.
Operators and skills
A line normally needs one operator for the extruders and die, one for the braider and yarn creel, and one for winding and packing on each shift. The braider operator is the critical role because yarn tension and break response decide the burst performance. Training on braid angle calculation and on the relationship between haul off speed and yarn pitch is more valuable than a longer machine warranty. Annual labor for a three person crew on two shifts is typically 180,000 to 340,000 US dollars.
15. Cost per Meter, Pricing and Payback
The table converts the investment into a unit cost for a 12 millimeter garden hose at three annual volumes. It assumes a standard phthalate compound, polyester yarn, one shift of operation and a four year depreciation period. All figures are in US dollars per meter of finished hose.
| Cost element | 2 million meters per year | 6 million meters per year | 15 million meters per year |
|---|---|---|---|
| PVC compound | 0.150 to 0.225 | 0.145 to 0.216 | 0.140 to 0.208 |
| Reinforcement yarn | 0.028 to 0.060 | 0.026 to 0.058 | 0.025 to 0.055 |
| Scrap and rework | 0.012 to 0.026 | 0.010 to 0.022 | 0.009 to 0.019 |
| Energy and water | 0.008 to 0.018 | 0.007 to 0.015 | 0.006 to 0.013 |
| Labor and supervision | 0.030 to 0.058 | 0.018 to 0.034 | 0.012 to 0.024 |
| Maintenance and consumables | 0.010 to 0.022 | 0.008 to 0.018 | 0.007 to 0.015 |
| Depreciation | 0.040 to 0.078 | 0.014 to 0.027 | 0.006 to 0.012 |
| Full cost | 0.278 to 0.487 | 0.228 to 0.390 | 0.205 to 0.346 |
| Wholesale selling price | 0.34 to 0.62 | 0.30 to 0.54 | 0.28 to 0.48 |
At six million meters a year the contribution is roughly 0.07 to 0.15 US dollars per meter, so a 480,000 US dollar line returns its capital in about 18 to 30 months. At two million meters a year the depreciation line dominates and payback stretches beyond three years. The two variables that move the result most are the selling price band and the scrap rate; improving yield from 94 to 97 percent is worth 30,000 to 70,000 US dollars a year on a medium line.
16. Wanplas Equipment Recommendation
Wanplas offers a PVC braided hose extrusion line for fiber reinforced garden hose from 8 to 50 millimeters. The line uses single screw extruders with strong plasticizing performance, a two claw haul off with variable frequency speed control, and can be configured for braided or knitted fiber layers, multiple colors, three layer and five layer constructions. The recommended configuration for a garden irrigation product is the 16 to 32 millimeter band with a 65 millimeter screw, 50 kilowatts total power, a 24 to 32 carrier braider, two cooling baths and an automatic winder.
A buyer starting in retail garden hose should choose the 8 to 12 millimeter band with a 45 millimeter screw and 35 kilowatts, then add a second die set for 16 millimeter product rather than buying an oversized line. A plant serving irrigation contractors should start at 16 to 32 millimeters and include the larger braider, because a small braider becomes the bottleneck as soon as pressure ratings rise. Wanplas supplies the companion equipment families as well, including PVC compounding and pelletizing lines, pipe and profile extrusion lines, recycling equipment for trim and scrap, chillers, dryers, loaders and inspection units. The service scope covers a 72 hour factory run, layout and utility drawings, installation, operator training, remote support and annual free spare parts valued at 500 US dollars.
17. Buying and Commissioning Checklist
Fix the hose diameters, wall thickness, working pressure and layer count before requesting a quotation. Ask for the screw diameter, total installed power and line speed at the actual product, not at water. Require a sample braid angle calculation and a written burst test result for the target construction. Confirm the number of braider carriers, the yarn creel capacity and the tensioning system. List the die sets included and the price of additional sets. Specify the haul off type, cooling bath length and winder capacity. Ask for a guaranteed output in meters per hour with an agreed definition of stops, and for a spare screw and a spare braider drive in the initial order.
During factory acceptance, run the line with the actual compound and yarn for four continuous hours. Measure outer diameter and wall thickness at four points around the circumference, check braid coverage, perform a hydrostatic hold and a burst test on samples, and verify that the length counter and winder hold tolerance. At site, repeat the same test, train the braider operators on tension and break response, and record the baseline values for every process parameter in the table above.
18. Frequently Asked Questions
What hose diameters can one line produce?
The official platform covers 8 to 50 millimeters in three bands: 8 to 12, 16 to 32, and 32 to 50 millimeters. Each band needs its own die set and braider setup, so a single line is normally purchased for one band with extra dies for nearby sizes.
Can the line make both braided and knitted hose?
Yes. With the appropriate head and yarn, the fiber layer can be crochet type or braided type. Braided hose is used for pressure service and knitted hose for light duty garden use at lower cost.
How many extruders does the line need?
Two. The first forms the inner tube, which is cooled and braided, and the second applies the outer cover through a crosshead die. A three layer or five layer product needs additional extrusion or additional braid stations.
What working pressure can a braided garden hose reach?
A 12 millimeter single braid hose is commonly rated near 8 to 12 bar, while a heavy duty 25 millimeter hose can reach 15 to 25 bar. Yarn strength, braid angle and layer bonding matter more than wall thickness alone.
Can scrap PVC be reused?
Clean trim can be reground and added at 10 to 20 percent to the inner layer. The outer cover should remain virgin compound for weather resistance, and fiber waste cannot be recycled.
How long does a diameter changeover take?
Typically 60 to 150 minutes. The die set, braider speed ratio, yarn creel and cooling settings all change, and the first produced meters must be checked for wall thickness and burst strength before sale.
What is the total installed power?
35 kilowatts for the 8 to 12 millimeter line with a 45 millimeter screw, 50 kilowatts for the 16 to 32 millimeter line with a 65 millimeter screw, and 60 kilowatts for the 32 to 50 millimeter line, before chillers and auxiliary equipment.
What payback period is realistic?
At six million meters a year, 18 to 30 months is typical for a 480,000 US dollar line. Below two million meters a year, payback usually exceeds three years and a smaller line or contract manufacturing should be considered.
19. Conclusion
A PVC fiber reinforced garden hose line turns two extrusions and one braiding step into a flexible pressure product. The official platform covers 8 to 50 millimeters with 45 or 65 millimeter screws and 35 to 60 kilowatts of installed power, and it can build single braid, three layer and five layer hose in several colors. The economics are driven by compound and yarn cost, braid quality and scrap rate, not by the nameplate speed of the extruders.
The two settings that decide whether a hose survives its pressure rating are the braid angle and the temperature of the inner tube when it enters the outer crosshead. A line that controls those two variables and stops on a yarn break will produce consistent hose; one that only watches barrel temperatures will not. A diameter gauge and a simple pressure rig are the first options worth adding to the base machine.
Wanplas supplies the complete line: two single screw extruders, dies, cooling tanks, braiding machine, haul off and winders, together with PVC compounding, recycling and auxiliary equipment. When requesting a proposal, share the target diameters, working pressure, layer count, yarn type, annual meterage and reel format, and ask for a signed output baseline, a burst test on your construction, a priced die set list and a spare parts schedule.

